Interface Selector

This combination of TL7075 and TL7076 provides a complete, high-performance optical fiber solution on one fiber line for the processing and transmission of high-end video data and is ideal for professional applications in the fields of surveillance, broadcasting, and video transmission.

SL4651 is a small form factor HD-TVI/AHD analog HD video transmitter for Block Cameras. Camera LVDS video input signals are demultiplexed, processed and output over a MCX coaxial connector. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B-0200 cable kit is included and contains 30wire micro coaxial cable for connecting SL4651 to the camera as well as 10wire power supply and serial control cable harness. Features: High Definition analog HD-TVI or AHD output 1080p30 /25 Hz 720p60 /50 Hz Small form factor Small form factor 55mm x 36mm Camera Control RS232 and TTL level serial control interface RS485 camera control interface (optional) Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Applications Full HD integrated cameras with analog HD YPbPr output requirements Industrial, medical, security, law enforcement Download SL4651 Datasheet V2.2.0 SL4651 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 4.08W (MP1110M-VC camera lens steady +SL4651) PD = 4.56W (FCB-EV7520A camera lens steady +SL4651) PSL4651 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4561 is RoHS compliant (2002/05/EG and 2011/65/EU) SL4651 PCB Connectors J6 HD-TVI/AHD output connector Samtec MCX7-J-P-H-RA-TH1 J5 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) SL4651 PCB Outline Onboard Mode Switch: Switch #1 SL4651 Video Output Mode: OFF=HD-TVI, ON=AHD Switch #2 Camera Monitoring Mode Adjust: OFF=No change, ON*=Force 1080p30 *SL4651 onbaord microcontroller adjusts camera video output setting to 1080p30 if switch #2 is in ON position. Checking switch #2 is done once during SL4651 boot cycle. Changing switch #2 position during board operation has no effect. Also switch #1 must be preset before power is applied to SL4651. SL4651 | Production Kit Partnumber Content SL4651 HD-TVI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n SL4651-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector

SL4655 is a small form factor analog YPbPr FHD video transmitter. Camera LVDS video input signals are demultiplexed, processed, converted to analog and output over 6pin board to wire connector. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B5 cable kit is included and contains 30wire micro coaxial cable for connecting SL4655 to the camera as well as 10wire power supply and serial control cable harness and a 6wire cable harness for the video output. Features: High Definition analog HD-YPbPr output 1080p30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25 Hz Small form factor Small form factor 55mm x 36mm Camera Control RS232 and TTL level serial control interface RS485 camera control interface (optional) Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Applications Full HD integrated cameras with analog HD YPbPr output requirements Industrial, medical, security, law enforcement Download SL4655 Datasheet V1.2.0 SL4655 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 4.08W (MP1110M-VC camera lens steady +SL4655) PD = 4.56W (FCB-EV7520A camera lens steady +SL4655) P SL4655 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4565 is RoHS compliant (2002/05/EG and 2011/65/EU) SL4655 PCB Connectors J5 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J7 YPbPr Video Output JST SM6B-SRSS-TB Pin Signal 1 Y signal output 2 GND (0V) 3 Pb signal output 4 GND (0V) 5 Pr signal outpu 6 GND (0V) SL4655 PCB Outline SL4655 | Production Kit Partnumber Content SL4655 FHD LVDS to analog YPbPr Board TLCK-B5 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K06-150 6 pin flying leads cable for YPbPr, length 15cm SL4655-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector

The TL3K7052 is a WQHD HDMI output video transmitter for block cameras from AIVION. It connects to the digital video interface of the block cameras and support several progressive and interlace HDTV formats. Features: One HDMI Output 1440p30 /25 Hz 1080p30 /25 Hz 720p30 /25Hz Small Form Factor Small form factor 46mm x 44mm Camera Control RS232 level serial camera control interface TTL level serial control interfac Temperature Range Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Temperature monitoring with alert function Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Power 9V to 12V DC regulated (13V DC absolute maximum) Download TL3K7052 V1.0.0 Datasheet TL3K7052 Block Diagram Power Input: 9V to 12V DC regulated (13V DC absolute maximum) Power consumption (incl. camera) 5.3W (cam motors inactive) Characteristics: PD = 5.6W (FCB-EV7520A camera lens steady +TL7055) PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/140°F - Humidity: 20%-80% TL3K7052 PCB Connectors J3 LVDS Video In 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J8 HDMI Camera Interface Kycon KDMIX_FS1V_WS or equivalent J1 Power and RS232/TTL Control IF JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera for reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) TL3K7052 PCB Outline Test Pattern Generator TL3K7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL3K7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL3K7052 power off and on again Note: For TPG operation on TL3K7052, the camera must be connected. TL3K7052 | Production Kit Partnumber Content TL3K7052 WQHD HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm TL3K7052-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

The TL4K1152 is a small form factor digital serial video transmitter from AIVION. Small form factor with an attractive price are some of the main features of the TL4K1152. It supports the new trend setting Sony block camera FCB 4K Series from Sony via an HDMI output. Camera control can be managed through an RS232 port. Via the available USB2 interface firmware updates can be obtained. Features: One HDMI 1.4b video output Up to 2160p30 UHD, FHD, HD video format support Integrated input signal equalizer Ultra high speed 3.4Gbps cable driver Small Form Factor Small form factor 46mm x 30mm Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control IF Temperature Range Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Compliance RoHS compliant (2002/05/EG and 2011/65/EU) Power Supply voltage 7V to 12V DC regulated Ultra low power - 150mW@8V supply voltage only Download TL4K1152 V2.0.0 Datasheet TL4K1152 Block Diagram Power Input: 7V to 12V DC regulated supply input voltage range Characteristics: PD = 3.05W (FCB-ER8300 lens steady +TL4K1152) PTL4K1152 = 150mW (typ.) (8V DC supply, 3840x2160@29.97fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1152 PCB Connectors J4 LVDS Video In 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J2 HDMI Camera Interface J1 Power and RS232/TTL Control IF Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V) 8 RXD_TTL (serial IF receive 3.3V) 9 RXD_232 (serial IF receive RS232) 10 TXD_232 (serial IF transmit RS232) J3 USB connector do not connect (for FCB-ER8300 firmware updates only). USB connector is no more assembled for revision B boards. TL4K1152 PCB Outline TL4K1152 | Production Kit Partnumber Content TL4K1152 HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1152-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

The TL4K1161 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed and output over coaxial connectors. Dual Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping, FHD output is compliant to SMPTE ST425-1 level A standards. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B-0200 cable kit is available as accessory. Features: SDI Video Output MCX 75 Ohm straight coaxial connectors Resolution up to 3840x2160p @ 30fps Dual Link 3G-SDI output of UHD formats 3G-SDI output of FHD formats 1.5G-SDI output of HD formats Automatic format detection Small Form Factor Small form factor 60mm x 46mm Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control IF Temperature Range and Power Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Application 4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530, FCB-ER8300, FCB-ES8230 and FCB-EW9500H camera blocks Industrial, medical, security, law enforcement, video production Download TL4K1161 V2.1.0 Datasheet TL4K1161 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 6.72W typ. (FCB-ER8300 lens steady +TL4K1161) P TL4K1161 = 3.72W (typ.) (12V DC supply, 3840x2160@25fps, TA = 25°C, Humidity = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1161 PCB Connectors J7 SDI output connector Link 1 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J8 SDI output connector Link 2 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J1 Power and Control IF Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 HDMI Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. TL4K1161 PCB Outline TL4K1161 | Production Kit Partnumber Content TL4K1161 Dual Link 3G-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1161-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws 2 x CK-MCX-BNC 2 MCX to BNC connector cable 

The TL4K1171 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed, and output over coaxial connectors. 6G-SDI output is compliant to SMPTE ST2081-10 MODE 1 mapping, Dual Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping and 3G-SDI FHD output is compliant to SMPTE ST425-1 level A standards. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B cable kit is available as accessory. Features: SDI Video Output Native signal processing for highest image quality MCX 75 Ohm straight coaxial connectors Resolution up to 3840x2160p @ 30fps 6G-SDI output of UHD formats Dual Link 3G-SDI output of UHD formats 3G-SDI output of FHD formats Automatic format detection Small Form Factor Small form factor 60mm x 46mm Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control interface Temperature Range and Power Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Application 4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530, FCB-ER8300, FCB-ES8230 and FCB-EW9500H camera blocks Industrial, medical, security, law enforcement, video production Download TL4K1171 V1.0.1 Datasheet TL4K1171 Block Diagram Power Input: 9V to 12V DC (12.5V DC max.) regulated supply input voltage range Characteristics: PD = 7.0W typ. (FCB-ER8530 lens steady +TL4K1171) P TL4K1171 = 3.9W (typ.) (12V DC supply, 3840x2160@29.97fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1171 PCB Connectors J1 Power and Control IF (JST SM10B-SRSS-TB) Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J3 External Sync (JST SM08B-SRSS-TB) for use with FCB-ER8550 only Pin Signal 1 GND (0V) 2 External Sync Loop Out 3 GND (0V) 4 ACC_LED (Output signal from FCB-ER8550) 5 GND (0V) 6 External Sync Input 7 GND (0V) 8 SYNC_LOCK (Output signal from FCB-ER8550) J4 HDMI Input (KEL USL00-30L-A) 30wire microcoax connector for FCB-ER8xxx and FCB-EW9500H. Use 30wire micro coaxial cable supplied with cable kit. J6 Board feature extension connector Contact us for further notice J7 + J8 SDI output connector (Samtec MCX7-J-P-H-ST-TH1) Mode J7 J8 UHD 6GbpsUHD mode selection by switch#2 No output 6G-SDI UHD 3GbpsUHD mode selection by switch#2 Link1 of Dual Link 3G-SDI Link2 of Dual Link 3G-SDI FHDFHD operation requires camera to be set to 1080p60, 1080p59.94 or 1080p50 GND (0V) 3G-SDI (same signal as J7) Board Config Switch   Switch# OFF ON 1 RS232 based camera control 3.3V TTL based camera control 2 6G-SDI UHD Output Mode DL 3G-SDI UHD Output Mode 3 Keep OFF Reserved 4 Keep OFF Reserved TL4K1171 PCB Outline TL4K1171 | Production Kit Partnumber Content TL4K1171 6 Gbps / Dual Link 3Gbps UHD-SDI Interface Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1171-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws 2 x CK-MCX-BNC MCX to BNC connector cable

The TL4K1261 is a small form factor serial digital video (SDI) transmitter from AIVION with Power and Control over Coaxial Cable. Camera video input signals are equalized, processed, and output over straight DIN7A(10.23) connectors. Dual Link 3G-SDI output compliant to SMPTE ST425-3, 2si mapping, FHD output compliant o SMPTE ST425-1 level A Camera control is accomplished by a transparent full-duplex communication channel. The physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B cable kit is included and contains a 30wire micro coaxial cable for connecting TL4K1261 to FCB-ER8300 as well as a 10wire power supply and serial control cable harness. Features: SDI Video Output DIN7A (10.23) 75 Ohm straight coaxial connectors Resolution up to 3840x2160p @ 30fps Dual Link 3 Gbps UHD-SDI Transmitter Dual Out 3/1.5 Gbps FHD-SDI Transmitter 3G-SDI output of FHD formats 1.5G-SDI output of HD formats Automatic format detection PCOC Power and Control over Coaxial Cable 100m Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control IF Temperature Range and Power Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Application 4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530 and FCB-ER8300 4K camera blocks Industrial, medical, security, law enforcement, video production Download TL4K1161 V1.1.0 Datasheet TL4K1261 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 6.72W typ. (FCB-ER8300 lens steady +TL4K1261) P TL4K1261 = 3.62W (typ.) (12V DC supply, 3840x2160@29.97fps, TA = 25°C, Humidity = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1261 PCB Connectors J7 SDI output connector Link 1 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J8 SDI output connector Link 2 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J1 Power and Control IF Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. TL4K1261 PCB Outline TL4K1261 | Production Kit Partnumber Content TL4K1261 Dual Link 3G-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1261-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws 2 x TL-EVK-DIN-BNC-1 2 Connector cables with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter 

The TL6032 interface is a HDTV USB 3.0 compliant video streaming capture solution from AIVION. As no analog to digital conversion is done on these modules, excellent output image quality is guaranteed. Features: USB 3.0 Video Output Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format 1920x1080p @ 25Hz, 29.97Hz, 30 Hz 1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer Small Form Factor Small form factor 45mm x 40mm USB Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported) Host computer must run a UVC capable operating system Parallel up- and downstream of camera control and status data is possible (USB CDC) Power Full USB bus powered camera solution possible depending on camera Power supply voltage for camera is generated onboard Allows an external power supply Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Temperature Range Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Download TL6032 V2.0.0 Datasheet TL6032 Block Diagram Power Input: 5V DC from USB3 port Characteristics: Power consumption (FCB-EV75xx + TL6035) 5.6W Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive) Power consumption TL6035: 2.7W/540mA@5V DC (max.) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80% TL6032 PCB Connectors J6 USB3 microB connector Horizontal J2 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. J7 External Power Supply Pin Signal 1 Input voltage 5V to 7V DC 2 Input voltage 5V to 7V DC 3 System reset, pull to GND for reset 4 GND (0V) 5 GND (0V) J9 RS232 UART Connector Pin Signal 1 to 7 do not connect 8 GND 9 RXD (host to camera) 10 TXD (camera to host) TL6032 PCB Outline Camera Power Camera supply voltage is generated on TL6032 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera. NOTE: USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6032. TL6032 EXTERNAL POWER OPTION: TL6032 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6032 for the camera supply boost converter only. All other electronic devices on TL6032 are always powered from USB3 port. No adjustments on TL6032 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power. Host (PC) - Device Communication TL6032 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6032 via a serial communication channel (USB UART). Connecting the TL6032 to the Host PC Operating System Support TL6032 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems: Windows 7 (32 and 64bit) Windows 8.1 (32 and 64bit) Windows 10 (64bit, version 1511) Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information. Controlling TL6032 from the Host PC via USB UART TL6032 supports the USB UART functionality. FCB cameras connected to TL6032 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1). TL6032 | Production Kit Partnumber Content TL6032 USB 3.0 Board TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL6032-EXT | Evaluation Extension Partnumber Content EK-PA1100-USB Power supply and control interface board PS-TE10A05 5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter TL-EVK-BRA Bracket and screws TL-EVK-USB3-A-MICROB USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector

The TL6035 USB 3.0 interface board from AIVION is a tiny and easy to use HDTV USB3.0 video capture interface for the block cameras. The module receives digital video signals and sends UVC (USB Videl Class) compliant data packets to a connected host computer. Our compact TL6035 module enables the design of small camera systems that need only a single connection between camera and PC. Video stream, control data and power will be connected by a USB 3.0 cable. For camera blocks that need more than 900 mA during startup a Y-cable is required. Features: USB 3.0 Video Output Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format 1920x1080p @ 25Hz, 29.97Hz, 30 Hz 1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer Small Form Factor Small form factor 45mm x 40mm USB Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported) Host computer must run a UVC capable operating system Parallel up- and downstream of camera control and status data is possible (USB CDC) Power Full USB bus powered camera solution possible depending on camera Power supply voltage for camera is generated onboard Allows an external power supply Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Temperature Range Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Datasheet TL6035 V2.0.0 Application Note TL6035 TL6035 Block Diagram Power Input: 5V DC from USB3 port Characteristics: Power consumption (FCB-EV75xx + TL6035) 5.6W Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive) Power consumption TL6035: 2.7W/540mA@5V DC (max.) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80% TL6035 PCB Connectors J6 USB3 microB connector Vertical J2 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. J7 External Power Supply Pin Signal 1 Input voltage 5V to 7V DC 2 Input voltage 5V to 7V DC 3 System reset, pull to GND for reset 4 GND (0V) 5 GND (0V) J9 RS232 UART Connector Pin Signal 1 to 7 do not connect 8 GND 9 RXD (host to camera) 10 TXD (camera to host) TL6035 PCB Outline Camera Power Camera supply voltage is generated on TL6035 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera. NOTE: USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6035. TL6035 EXTERNAL POWER OPTION: TL6035 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6035 for the camera supply boost converter only. All other electronic devices on TL6035 are always powered from USB3 port. No adjustments on TL6035 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power. Host (PC) - Device Communication TL6035 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6035 via a serial communication channel (USB UART). Connecting the TL6035 to the Host PC Operating System Support TL6035 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems: Windows 7 (32 and 64bit) Windows 8.1 (32 and 64bit) Windows 10 (64bit, version 1511) Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information. Controlling TL6035 from the Host PC via USB UART TL6035 supports the USB UART functionality. FCB cameras connected to TL6035 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1). TL6035 | Production Kit Partnumber Content TL6035 USB 3.0 Vertical Micro B USB Board TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL6035-EXT | Evaluation Extension Partnumber Content EK-PA1100-USB Power supply and control interface board PS-TE10A05 5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter TL-EVK-BRA Bracket and screws TL-EVK-USB3-A-MICROB USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector

The TL6636 USB 3.0 interface board with trigger functionality from AIVION is tiny and easy to use HDTV USB3.0 video capture interface for the block cameras. The module receives digital video signals and sends UVC (USB Videl Class) compliant data packets to a connected host computer. Our compact TL6636 module enables the design of small camera systems that need only a single connection between the camera and PC. Video stream, control data and power will be connected by a USB 3.0 cable. For camera blocks that need more than 900 mA during startup, a Y-cable is required. Features: USB 3.0 Video Output Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format 1920x1080p @ 25Hz, 29.97Hz, 30 Hz 1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer Trigger Real-time external trigger input for MP2030M-GS global shutter camera block Single LVDS data format provided by Tamron camera blocks USB Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported) Host computer must run a UVC capable operating system Parallel up- and downstream of camera control and status data is possible (USB CDC) Power Full USB bus powered camera solution possible depending on camera Power supply voltage for camera is generated onboard Allows an external power supply Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Temperature Range Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Download TL6636 V2.0.0 Datasheet TL6636 Block Diagram Power Input: 5V DC from USB3 port Characteristics: Power consumption (MP2030M-GS + TL6636) 7.65W (cam motors inactive) Power consumption (MP2030M-GS + TL6636) 9.3W (boot cyle and cam motors active) Power consumption TL6636: 2.7W/540mA@5V DC (max.) Power consumption value conditions: Camera monitoring mode set to 1080p30 Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80% TL6636 PCB Connectors J6 USB3 microB connector Vertical J2 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. J7 External Power Supply Pin Signal 1 Input voltage 5V to 7V DC 2 Input voltage 5V to 7V DC 3 System reset, pull to GND for reset 4 GND (0V) 5 GND (0V) J9 RS232 UART Connector Pin Signal 1 External trigger pulse* input, 3.3V max. Active high trigger pulse duration must be 1us minimum. Trigger pulse input has a 10kohms pullup resistor 2 Trigger demo mode select input**, 3.3V max. Trigger mode select input has a 10kohms pulldown resistor 3 do not connect 4 Trigger response output 5 3.3V output (20mA max.) 6 do not connect 7 do not connect 8 GND 9 RXD (host to camera) 10 TXD (camera to host) TL6636 PCB Outline Camera Power Camera supply voltage is generated on TL6636 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera. NOTE: USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3.0 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3.0 output power is sufficient or not. This is in the sole responsibility of the user of TL6636. In case the host computer provides a USB3.1 port, it is recommended to use this one instead of a USB3.0 port. TL6636 EXTERNAL POWER OPTION: TL6636 allows to use an external power supply in case USB3 power of the computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6636 for the camera supply boost converter only. All other electronic devices on TL6636 are always powered from USB3 port. No adjustments on TL6636 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power. EXTERNAL POWER USE PER CAMERA MODEL: MP2030M-GS: Recommended, should be used MP1010M-VC: Not required but can be used MP1110M-VC: Not required but can be used Host (PC) - Device Communication TL6636 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6636 via a serial communication channel (USB UART). Connecting the TL6636 to the Host PC Operating System Support TL6636 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems: Windows 7 (32 and 64bit) Windows 8.1 (32 and 64bit) Windows 10 (64bit, version 1511) Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information. Controlling TL6636 from the Host PC via USB UART TL6636 supports the USB UART functionality. FCB cameras connected to TL6636 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1). Real-Time external Trigger Operation NOTE: EXTERNAL TRIGGER IS AVAILABLE WITH MP2030M-GS ONLY. Tamron’s MP2030M-GS global shutter block camera module allows for real- time triggered still image capture. Refer to MP2030M-GS technical manual provided by Tamron for details on real-time triggered still image capture operation. TL6636 USB3 full HD video streamer provides a trigger mode input for selecting one out of two available trigger modes. Mode 1 (default, pin2/J9 0V or open): External direct trigger Trigger pulse input on pin1/J9 is glitch filtered and driven to MP2030M-GS trigger input po Mode 2 (pin2/J9 3.3V): Automatic periodic trigger (demo mode) After selecting and activating trigger mode at MP2030M-GS by the related VISCA commands, the automatic trigger period is set to 1.5s. In this demo mode the camera takes an image every 1.5s (approx.). TL6636 | Production Kit Partnumber Content TL6636 USB 3.0 Vertical (Trigger) TLCK-B 1. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 2. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 3. TLCK-FL05-150 5 pin flying leads cable for external power, length 15cm TL6636-EXT | Evaluation Extension Partnumber Content EK-PA1100-USB Power supply and control interface board PS-TE10A05 5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter PTL-EVK-BRA Bracket and screws TL-EVK-USB3-A-MICROB USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector

The TL7050 Dual 3G/HD-SDI and DVI(HDMI) Output Video Transceiver module from AIVION connect to the digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M  HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One HDMI Output HDMI connector (Kycon KDMIX_FS1V_WS) 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Video input and Compliance Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7050 V 2.5.0 Datasheet TL7050 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Characteristics: Power consumption TL7050: 260mA @ 12V DC (typ.) Operating and Storage Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7050 PCB Connectors J8 HDMI connector Kycon KDMIX_FS1V_WS J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7050 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output TL7050 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7050 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7050 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7050 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7050 Analog Video Output TL7050 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7050, the camera is also automatically powered. During power up all functions on TL7050, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7050. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7050 | Production Kit Partnumber Content TL7050 HDMI-HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7050-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

The TL7051 Dual 3G/HD-SDI Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and supports several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M  HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7051 Revision D V.3.0.0 Datasheet TL7051 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7051 PCB Connectors J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7051 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7051 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND TL7051 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low ( < 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7051 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7051 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7051 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7051 Analog Video Output TL7051 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7051, the camera is also automatically powered. During power up all functions on TL7051, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7051. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7051 | Production Kit Partnumber Content TL7051 3G-SDI/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7051-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable

The TL7052 DVI(HDMI) Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera One HDMI Output HDMI connector (Kycon KDMIX_FS1V_WS) 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7052 V 2.4.0 Datasheet TL7052 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7052 PCB Connectors J8 HDMI connector Kycon KDMIX_FS1V_WS J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7052 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 Analog component YPbPr and CVBS output Requires TL7052 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND J4 24pin FFC Connector Power, Reset, Serial Control IF, analog Video TL7052 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7052 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7052 Analog Video Output TL7052 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7052, the camera is also automatically powered. During power up all functions on TL7052, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7052. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7052 | Production Kit Partnumber Content TL7052 HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7052-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector. Features: One 3G-SDI/HD-SDI Output MCX connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One Analog YsPbPr Output 8pin board to wire connector Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV Pb, Pr 0,7Vpp into 75 ohms 1080p60 /59.94 /50 /30 /29.97 /25 Hz 720p60 /59.94 /50 Hz Camera Control RS232 level serial camera control interface Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface. Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Small form factor & Compliance Small form factor 46mm x 44mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements Industrial, medical, security, law enforcement Download TL7055 Datasheet TL7055 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 5.6W (FCB-EV7520A camera lens steady +TL7055) PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU) TL7055 PCB Connectors J8 SDI Video Output Samtec MCX7-J-P-H-ST-SM1 J7 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J2 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 Do not connect 8 Do not connect 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 YPbPr Video Output JST SM08B-SRSS-TB Pin Signal 1 HSync 2 VSync 3 GND (0V) 4 Pb signal output 5 GND (0V) 6 Ys signal output 7 GND (0V) 8 Pr signal output TL7055 PCB Outline Board Operation: TL7055 TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal. The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes). The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as 7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels. In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode. TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera. When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details). The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055. Test Pattern Generator (TPG) mode: TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default. TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards. The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control. The following VISCA commands are available for TPG control (all codes as hex values): TPG activation: 87 01 00 24 01 08 0A FF TPG deactivation: 87 01 00 24 01 08 06 FF TPG pattern type 100% color bar: 87 01 00 24 04 00 04 FF TPG pattern type multi pattern with moving block: 87 01 00 24 04 00 00 FF TPG video standard: 87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50 pq = 19 for 720p60 TL7055 | Production Kit Partnumber Content TL7055 3G-SDI & analog Board TLCK-B6 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K08-150 8wire cable harness for the analog YsPbPr video output TL7055-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter CK-MCX-BNC MCX to BNC connector cable

+ Digital LVDS video input from camera+ 1080i, 1080p and 720p output standard support+ 25Hz, 29.97Hz, 30Hz, 50Hz, 59.94Hz and 60Hz frame rates+ Automatic camera and video standard detection+ Optical 3G/HD-SDI output based on SFP compatible transmitter+ Optical transmitter 1310nm/10km/LC for SMF included+ BNC + MCX coax 3G/HD-SDI outputs+ HD-SDI outputs compliant to SMPTE425M/424M/292M/274M/296M+ DVI (HDMI connector) video output+ Native digital signal processing chain for best image quality (no scaling)+ Breakout of camera analog HDTV YPbPr and CVBS video+ Dual serial control interface (RS232 or 3.3V TTL)+ Supply voltage: 7V to 12V DC regulated (5V only when used with FCB-SE600)

+ Optical 3G/HD-SDI input based on SFP compatible receiver+ Optical SFP receiver 1260nm-1620nm/10km/LC for SMF included+ Input compliant to SMPTE297M-2006 serial optical 3G/HD video standards + Automatic video standard detection+ Input signal jitter removal+ Format conversion for DVI(HDMI) RGB output+ Reclocked 3G/HD-SDI BNC + MCX coax outputs+ 3G/HD-SDI outputs compliant to SMPTE425M/424M/292M/274M/296M+ SMPTE425M level A, mapping structure 1+ Selectable serial control interface (RS232 or 3.3V TTL)+ Supply voltage: 5V to 12V DC regulated

The AIVION TL8651 outputs serial digital video (SDI) up to 1080p60. It connects to the digital video interface of the block cameras and supports several progressive and interlace HDTV formats. Features: One 3G-SDI/HD-SDI Output Right angle DIN7A connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Board Side Mount The TL8651 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras. Tamron MP1010M-VC Tamron MP1110M-VC Camera Control RS232 and TTL level serial control interface Temperature Range and Power Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9.5V to 12V DC regulated Small form factor & Compliance Small form factor 60mm x 36mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Industrial, medical, security, inspection, ROV and Security Download TL8651 Datasheet TL8651 Block Diagram Power Input: 9.5V to 12V DC regulated supply input voltage range Power consumption (MP1110M-VC + TL8651) 4.7W (cam motors inactive) Power consumption value conditions: Power 12V DC, video mode 1080p60 Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80% Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80% TL8651 PCB Connectors J2 KEL USL00-30L-A Camera IF, use supplied 30wire micro coaxial cable only J4 3G/HD-SDI output KEL USL00-30L-A Default type: CEI C-SX113 (DIN7A / 1.0/2.3 coax system) J3 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC In 2 DC In 3 GND 4 GND 5 Reset / Shut Down, pull to GND to reset/shut down TL7650 and camera for reset, pull to GND for one second or longer 6 GND 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 CVBS Output JST SM03B-SRSS-TB Pin Signal 1 GND 2 CVBS analog video output 3 GND (0V) CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details. In NTSC or PAL mode, there will be no SDI output signal available from TL8651. CVBS output connector J5 is available on Rev.B boards from September 26, 2018. TL8651 PCB Outline TL8651 | Production Kit Partnumber Content TL8651 3G/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL8651-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-DIN-BNC-1 Connector cable with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter

The TL8652 HDMI Output Video Transceiver module from AIVION connect to the digital video interface of the block cameras and support several progressive and interlace HDTV formats. TL8652 outputs HDMI up to 1080p60. Features: HDMI 1.4 output RGB444 or YCbCr422 colour format selectable 1080p60 /50 /30 /25 Hz 1080i60 /50 Hz 720p60 /50 Hz Board Side Mount The TL8652 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras. Tamron MP1010M-VC Tamron MP1110M-VC Camera Control RS232 and TTL level serial control interface Integrated USB2 UART for camera control Temperature Range Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Small form factor & Compliance Small form factor 61mm x41mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Power USB powered 5V DC Download TL8652 V2.2.0 Datasheet TL8652 Block Diagram Power Input: 5V DC over USB2 micro connector (USB3 host port or powered USB3 hub required) Power consumption (MP1010M-VC + TL8652) 4.5W/900mA (cam motors inactive) Power consumption TL8652: 1.5W, 300mA @ 5V DC (typ.) Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80% Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80% TL8652 PCB Connectors J6 KEL USL00-30L-A Camera IF, use supplied 30wire micro coaxial cable only J3 HDMI micro connector J2 USB2 micro connector J1 Reset and RS232 Control IF JST SM10B-SRSS-TB Pin Signal 1 Do not connect 2 Do not connect 3 GND 4 GND 5 Reset / Shut Down, pull to GND to reset/shut down TL8652 and camera for reset, pull to GND for one second or longer 6 GND 7 Do not connect 8 Do not connect 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J7 CVBS Output JST SM03B-SRSS-TB Pin Signal 1 GND 2 CVBS analog video output 3 GND (0V) CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details. In NTSC or PAL mode, there will be no HDMI output signal available from TL8652/A. TL8652 PCB Outline TL8652 | Production Kit Partnumber Content TL8652 HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL8652-EXT | Evaluation Extension Partnumber Content TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector Driver Installer Package and Cypress USB-Serial Driver Installation Guide for the USB2 UART Chip are online available. TL-EVK-HDMI-MICRO-D High Speed HDMI Cable 1 with HDMI-A 19 and 1 HDMI Micro-D 19 pin male connector 

The AIVION TL8656 outputs serial digital video (SDI) up to 1080p60 with Power and Control over Coaxial Cable and an external Trigger. It connects to the digital video interface of the block cameras and supports several progressive and interlace HDTV formats. Features: One 3G-SDI/HD-SDI Output Right angle DIN7A connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Board Side Mount The TL8656 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras. Tamron MP1010M-VC Tamron MP1110M-VC Camera Control RS232 and TTL level serial control interface Power and Control over Coaxial Cable Ext. Trigger Temperature Range and Power Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9.5V to 12V DC regulated Small form factor & Compliance Small form factor 60mm x 36mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Industrial, medical, security, inspection, ROV and Security Download TL8656 Datasheet TL8656 Block Diagram Power Input: 9.5V to 12V DC regulated supply input voltage range Power consumption (MP1110M-VC + TL8656) 4.7W (cam motors inactive) Power consumption value conditions: Power 12V DC, video mode 1080p60 Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80% Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80% TL8656 PCB Connectors J2 KEL USL00-30L-A Camera IF, use supplied 30wire micro coaxial cable only J4 3G/HD-SDI output KEL USL00-30L-A Default type: CEI C-SX113 (DIN7A / 1.0/2.3 coax system) J3 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC In 2 DC In 3 GND 4 GND 5 Reset / Shut Down, pull to GND to reset/shut down TL7650 and camera for reset, pull to GND for one second or longer 6 GND 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 CVBS Output JST SM03B-SRSS-TB Pin Signal 1 GND 2 CVBS analog video output 3 GND (0V) CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details. In NTSC or PAL mode, there will be no SDI output signal available from TL8656. CVBS output connector J5 is available on Rev.B boards from September 26, 2018. TL8656 PCB Outline TL8656 | Production Kit Partnumber Content TL8656 3G/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm Type (1:n) TL8656-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-DIN-BNC-1 Connector cable with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter

The TL9801 CVBS analog video interface from AIVION is a small form factor module to convert LVDS. Features: CVBS analog video output CVBS pass through from camera. Camera must be set to CVBS PAL or NTSC operating mode. Small form factor Small form factor 44mm x 38mm Camera Control USB2 UART based camera control Power 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Temperature Range Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Download TL9801 Datasheet V1.0.0 TL9801 Block Diagram Power Input: 9V TO 12V regulated Power consumption (MP1110M-VC + TL9801) 3.2 W (cam motors inactive) Operating and Storage Conditions: Operating: Ambient Temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% Storage: Ambient Temperature (min/max): -20°C/+60°C = -4°F/140°FHumidity: 20%-80% TL9801 PCB Connectors J1 DC Jack Fitting plug inner/outer diameter: 2.55mm/5,5mm Center Pin DC Power Input - Shield GND J2 USB2 micro connector USB2 UART camera control interface USB2 UART chip Cypress CY7C65213 J5 MCX Coaxial connector Primary CVBS Output J9 Micro coaxial connector J6 CVBS Output (Board to wire connector) JST BM08B-SSRS-TB Pin Signal 1 CVBS Output (alternative to J5, do not connect both) 2 GND 3 Do not connect 4 Do not connect 5 Do not connect 6 GND (0V) 7 Do not connect 8 Do not connect TL9801 PCB Outline TL9801 | Production Kit Partnumber Content TL9801 CVBS Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm (Type 1:n) TL9801-EXT | Evaluation Extension Partnumber Content PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector CK-MCX-BNC MCX to BNC connector cable