AIVION announces the SL4651 - a new Full-HD TVI / AHD video interface for block cameras

SL4651 is a small form factor HD-TVI/AHD analog HD video transmitter for Block Cameras. Camera LVDS video input signals are demultiplexed, processed and output over a MCX coaxial connector. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B-0200 cable kit is included and contains 30wire micro coaxial cable for connecting SL4651 to the camera as well as 10wire power supply and serial control cable harness. Features: High Definition analog HD-TVI or AHD output 1080p30 /25 Hz 720p60 /50 Hz Small form factor Small form factor 55mm x 36mm Camera Control RS232 and TTL level serial control interface RS485 camera control interface (optional) Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Applications Full HD integrated cameras with analog HD YPbPr output requirements Industrial, medical, security, law enforcement Download SL4651 Datasheet V2.2.0 SL4651 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 4.08W (MP1110M-VC camera lens steady +SL4651) PD = 4.56W (FCB-EV7520A camera lens steady +SL4651) PSL4651 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4561 is RoHS compliant (2002/05/EG and 2011/65/EU) SL4651 PCB Connectors J6 HD-TVI/AHD output connector Samtec MCX7-J-P-H-RA-TH1 J5 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) SL4651 PCB Outline Onboard Mode Switch: Switch #1 SL4651 Video Output Mode: OFF=HD-TVI, ON=AHD Switch #2 Camera Monitoring Mode Adjust: OFF=No change, ON*=Force 1080p30 *SL4651 onbaord microcontroller adjusts camera video output setting to 1080p30 if switch #2 is in ON position. Checking switch #2 is done once during SL4651 boot cycle. Changing switch #2 position during board operation has no effect. Also switch #1 must be preset before power is applied to SL4651. SL4651 | Production Kit Partnumber Content SL4651 HD-TVI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n SL4651-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector

SL4655 is a small form factor analog YPbPr FHD video transmitter. Camera LVDS video input signals are demultiplexed, processed, converted to analog and output over 6pin board to wire connector. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B5 cable kit is included and contains 30wire micro coaxial cable for connecting SL4655 to the camera as well as 10wire power supply and serial control cable harness and a 6wire cable harness for the video output. Features: High Definition analog HD-YPbPr output 1080p30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25 Hz Small form factor Small form factor 55mm x 36mm Camera Control RS232 and TTL level serial control interface RS485 camera control interface (optional) Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Applications Full HD integrated cameras with analog HD YPbPr output requirements Industrial, medical, security, law enforcement Download SL4655 Datasheet V1.2.0 SL4655 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 4.08W (MP1110M-VC camera lens steady +SL4655) PD = 4.56W (FCB-EV7520A camera lens steady +SL4655) P SL4655 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4565 is RoHS compliant (2002/05/EG and 2011/65/EU) SL4655 PCB Connectors J5 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J7 YPbPr Video Output JST SM6B-SRSS-TB Pin Signal 1 Y signal output 2 GND (0V) 3 Pb signal output 4 GND (0V) 5 Pr signal outpu 6 GND (0V) SL4655 PCB Outline SL4655 | Production Kit Partnumber Content SL4655 FHD LVDS to analog YPbPr Board TLCK-B5 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K06-150 6 pin flying leads cable for YPbPr, length 15cm SL4655-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector

The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector. Features: One 3G-SDI/HD-SDI Output MCX connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One Analog YsPbPr Output 8pin board to wire connector Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV Pb, Pr 0,7Vpp into 75 ohms 1080p60 /59.94 /50 /30 /29.97 /25 Hz 720p60 /59.94 /50 Hz Camera Control RS232 level serial camera control interface Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface. Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Small form factor & Compliance Small form factor 46mm x 44mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements Industrial, medical, security, law enforcement Download TL7055 Datasheet TL7055 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 5.6W (FCB-EV7520A camera lens steady +TL7055) PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU) TL7055 PCB Connectors J8 SDI Video Output Samtec MCX7-J-P-H-ST-SM1 J7 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J2 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 Do not connect 8 Do not connect 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 YPbPr Video Output JST SM08B-SRSS-TB Pin Signal 1 HSync 2 VSync 3 GND (0V) 4 Pb signal output 5 GND (0V) 6 Ys signal output 7 GND (0V) 8 Pr signal output TL7055 PCB Outline Board Operation: TL7055 TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal. The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes). The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as 7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels. In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode. TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera. When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details). The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055. Test Pattern Generator (TPG) mode: TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default. TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards. The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control. The following VISCA commands are available for TPG control (all codes as hex values): TPG activation: 87 01 00 24 01 08 0A FF TPG deactivation: 87 01 00 24 01 08 06 FF TPG pattern type 100% color bar: 87 01 00 24 04 00 04 FF TPG pattern type multi pattern with moving block: 87 01 00 24 04 00 00 FF TPG video standard: 87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50 pq = 19 for 720p60 TL7055 | Production Kit Partnumber Content TL7055 3G-SDI & analog Board TLCK-B6 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K08-150 8wire cable harness for the analog YsPbPr video output TL7055-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter CK-MCX-BNC MCX to BNC connector cable