Serial Digital Interfaces
Filter
–
The TL4K1161 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed and output over coaxial connectors. Dual Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping,
FHD output is compliant to SMPTE ST425-1 level A standards. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level.
TLCK-B-0200 cable kit is available as accessory.
Features:
SDI Video Output
MCX 75 Ohm straight coaxial connectors
Resolution up to 3840x2160p @ 30fps
Dual Link 3G-SDI output of UHD formats
3G-SDI output of FHD formats
1.5G-SDI output of HD formats
Automatic format detection
Small Form Factor
Small form factor 60mm x 46mm
Camera Control
RS232 level serial camera control interface
3.3V TTL level serial camera control IF
Temperature Range and Power
Ambient temperature (min/max): -5°C/+60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC regulated
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Application
4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530, FCB-ER8300, FCB-ES8230 and FCB-EW9500H camera blocks
Industrial, medical, security, law enforcement, video production
Download TL4K1161 V2.1.0 Datasheet
TL4K1161 Block Diagram
Power Input:
9V to 12V DC regulated supply input voltage range
Characteristics:
PD = 6.72W typ. (FCB-ER8300 lens steady +TL4K1161)
P TL4K1161 = 3.72W (typ.) (12V DC supply, 3840x2160@25fps, TA = 25°C, Humidity = 40%)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
TL4K1161 PCB Connectors
J7 SDI output connector
Link 1 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output
J8 SDI output connector
Link 2 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output
J1 Power and Control IF
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
TXD_TTL (serial IF transmit 3.3V, optional)
8
RXD_TTL (serial IF receive 3.3V, optional)
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
J4 HDMI Video In
30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit.
TL4K1161 PCB Outline
TL4K1161 | Production Kit
Partnumber
Content
TL4K1161
Dual Link 3G-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL4K1161-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
TL-EVK-BRA
Bracket and screws
2 x CK-MCX-BNC
2 MCX to BNC connector cable
Price on request
The TL4K1171 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed, and output over coaxial connectors. 6G-SDI output is compliant to SMPTE ST2081-10 MODE 1 mapping, Dual
Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping and 3G-SDI FHD output is compliant to SMPTE ST425-1 level A standards. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between
camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B cable kit is available as accessory.
Features:
SDI Video Output
Native signal processing for highest image quality
MCX 75 Ohm straight coaxial connectors
Resolution up to 3840x2160p @ 30fps
6G-SDI output of UHD formats
Dual Link 3G-SDI output of UHD formats
3G-SDI output of FHD formats
Automatic format detection
Small Form Factor
Small form factor 60mm x 46mm
Camera Control
RS232 level serial camera control interface
3.3V TTL level serial camera control interface
Temperature Range and Power
Ambient temperature (min/max): -5°C/+60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Application
4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530, FCB-ER8300, FCB-ES8230 and FCB-EW9500H camera blocks
Industrial, medical, security, law enforcement, video production
Download TL4K1171 V1.0.1 Datasheet
TL4K1171 Block Diagram
Power Input:
9V to 12V DC (12.5V DC max.) regulated supply input voltage range
Characteristics:
PD = 7.0W typ. (FCB-ER8530 lens steady +TL4K1171)
P TL4K1171 = 3.9W (typ.) (12V DC supply, 3840x2160@29.97fps, TA = 25°C, Humididty = 40%)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
TL4K1171 PCB Connectors
J1 Power and Control IF
(JST SM10B-SRSS-TB)
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
TXD_TTL (serial IF transmit 3.3V, optional)
8
RXD_TTL (serial IF receive 3.3V, optional)
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
J3 External Sync
(JST SM08B-SRSS-TB) for use with FCB-ER8550 only
Pin
Signal
1
GND (0V)
2
External Sync Loop Out
3
GND (0V)
4
ACC_LED (Output signal from FCB-ER8550)
5
GND (0V)
6
External Sync Input
7
GND (0V)
8
SYNC_LOCK (Output signal from FCB-ER8550)
J4 HDMI Input
(KEL USL00-30L-A)
30wire microcoax connector for FCB-ER8xxx and FCB-EW9500H. Use 30wire micro coaxial cable supplied with cable kit.
J6 Board feature extension connector
Contact us for further notice
J7 + J8 SDI output connector
(Samtec MCX7-J-P-H-ST-TH1)
Mode
J7
J8
UHD 6GbpsUHD mode selection by switch#2
No output
6G-SDI
UHD 3GbpsUHD mode selection by switch#2
Link1 of Dual Link 3G-SDI
Link2 of Dual Link 3G-SDI
FHDFHD operation requires camera to be set to 1080p60, 1080p59.94 or 1080p50
GND (0V)
3G-SDI (same signal as J7)
Board Config Switch
Switch#
OFF
ON
1
RS232 based camera control
3.3V TTL based camera control
2
6G-SDI UHD Output Mode
DL 3G-SDI UHD Output Mode
3
Keep OFF
Reserved
4
Keep OFF
Reserved
TL4K1171 PCB Outline
TL4K1171 | Production Kit
Partnumber
Content
TL4K1171
6 Gbps / Dual Link 3Gbps UHD-SDI Interface Board
TLCK-B
1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL4K1171-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
2 x CK-MCX-BNC
MCX to BNC connector cable
Price on request
The TL4K1261 is a small form factor serial digital video (SDI) transmitter from AIVION with Power and Control over Coaxial Cable. Camera video input signals are equalized, processed, and output over straight DIN7A(10.23) connectors. Dual Link 3G-SDI output compliant to SMPTE ST425-3, 2si mapping, FHD output compliant o SMPTE ST425-1 level A Camera control is accomplished by a transparent full-duplex communication channel. The physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B cable kit is included and contains a 30wire micro coaxial cable for connecting TL4K1261 to FCB-ER8300 as well as a 10wire power supply and serial control cable harness.
Features:
SDI Video Output
DIN7A (10.23) 75 Ohm straight coaxial connectors
Resolution up to 3840x2160p @ 30fps
Dual Link 3 Gbps UHD-SDI Transmitter
Dual Out 3/1.5 Gbps FHD-SDI Transmitter
3G-SDI output of FHD formats
1.5G-SDI output of HD formats
Automatic format detection
PCOC
Power and Control over Coaxial Cable 100m
Camera Control
RS232 level serial camera control interface
3.3V TTL level serial camera control IF
Temperature Range and Power
Ambient temperature (min/max): -5°C/+60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC regulated
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Application
4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530 and FCB-ER8300 4K camera blocks
Industrial, medical, security, law enforcement, video production
Download TL4K1161 V1.1.0 Datasheet
TL4K1261 Block Diagram
Power Input:
9V to 12V DC regulated supply input voltage range
Characteristics:
PD = 6.72W typ. (FCB-ER8300 lens steady +TL4K1261)
P TL4K1261 = 3.62W (typ.) (12V DC supply, 3840x2160@29.97fps, TA = 25°C, Humidity = 40%)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
TL4K1261 PCB Connectors
J7 SDI output connector
Link 1 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output
J8 SDI output connector
Link 2 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output
J1 Power and Control IF
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
TXD_TTL (serial IF transmit 3.3V, optional)
8
RXD_TTL (serial IF receive 3.3V, optional)
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
J4 LVDS Video In
30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit.
TL4K1261 PCB Outline
TL4K1261 | Production Kit
Partnumber
Content
TL4K1261
Dual Link 3G-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL4K1261-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
TL-EVK-BRA
Bracket and screws
2 x TL-EVK-DIN-BNC-1
2 Connector cables with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter
Price on request
The TL7050 Dual 3G/HD-SDI and DVI(HDMI) Output Video Transceiver module from AIVION connect to the
digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV
formats. As no analog to digital conversion is done on these modules, excellent output image quality is
achieved.
Features:
Dual 3G-SDI/HD-SDI Output
3G-SDI output compliant to SMPTE 424M level A
HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
One HDMI Output
HDMI connector (Kycon KDMIX_FS1V_WS)
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Robust RS485 differential serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Video input and Compliance
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7050 V 2.5.0 Datasheet
TL7050 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Characteristics:
Power consumption TL7050: 260mA @ 12V DC (typ.)
Operating and Storage Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7050 PCB Connectors
J8 HDMI connector
Kycon KDMIX_FS1V_WS
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera. For reset, pull to GND for
one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J2 RS485 Control IF
JST SM08B-SRSS-TB
Pin
Signal
1
TXD_P (to controller)
2
TXD_N (to controller)
3
RXD_N (from controller)
4
RXD_P (from controller)
5
GND
6
3.45V typ. (max. current 50mA)
J5 Analog component YPbPr and CVBS output
Requires TL7050 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output
TL7050 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V)
- In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7050 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7050 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7050 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7050
Analog Video Output
TL7050 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera.
In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation.
Reset Operation
When applying power to TL7050, the camera is also automatically powered. During power up all functions on TL7050, are reset and initialized.
During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7050. The interface is passed through to the camera that all VISCA protocol based software can be used.
Serial interface selection must be done be appropriate setting of switch-2.
TL7050 | Production Kit
Partnumber
Content
TL7050
HDMI-HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL7050-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
CK-MCX-BNC
MCX to BNC connector cable
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
Price on request
The TL7051 Dual 3G/HD-SDI Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and supports several progressive and interlace HDTV formats. As no analog to digital conversion is done on
these modules, excellent output image quality is achieved.
Features:
Dual 3G-SDI/HD-SDI Output
3G-SDI output compliant to SMPTE 424M level A
HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Video input
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Robust RS485 differential serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7051 Revision D V.3.0.0 Datasheet
TL7051 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Operating Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7051 PCB Connectors
J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7051 and camera. For reset, pull to GND for one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J2 RS485 Control IF
JST SM08B-SRSS-TB
Pin
Signal
1
TXD_P (to controller)
2
TXD_N (to controller)
3
RXD_N (from controller)
4
RXD_P (from controller)
5
GND
6
3.45V typ. (max. current 50mA)
J5 Analog component YPbPr and CVBS output
Requires TL7051 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
TL7051 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (
<
0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7051 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7051 board. In addition one out of two
test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7051 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7051
Analog Video Output
TL7051 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related
camera documentation.
Reset Operation
When applying power to TL7051, the camera is also automatically powered. During power up all functions on TL7051, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND).
This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7051. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection
must be done be appropriate setting of switch-2.
TL7051 | Production Kit
Partnumber
Content
TL7051
3G-SDI/HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL7051-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
CK-MCX-BNC
MCX to BNC connector cable
Price on request
The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector.
Features:
One 3G-SDI/HD-SDI Output
MCX connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
One Analog YsPbPr Output
8pin board to wire connector Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV Pb, Pr 0,7Vpp into 75 ohms
1080p60 /59.94 /50 /30 /29.97 /25 Hz
720p60 /59.94 /50 Hz
Camera Control
RS232 level serial camera control interface
Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface.
Temperature Range and Power
Operating ambient temperature range -10°C to +60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC regulated
Small form factor & Compliance
Small form factor 46mm x 44mm
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Applications
Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements
Industrial, medical, security, law enforcement
Download TL7055 Datasheet
TL7055 Block Diagram
Power Input:
9V to 12V DC regulated supply input voltage range
Characteristics:
PD = 5.6W (FCB-EV7520A camera lens steady +TL7055)
PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%)
Operating and Storage Conditions:
Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU)
TL7055 PCB Connectors
J8 SDI Video Output
Samtec MCX7-J-P-H-ST-SM1
J7 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J2 Power & Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
Do not connect
8
Do not connect
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
J4 YPbPr Video Output
JST SM08B-SRSS-TB
Pin
Signal
1
HSync
2
VSync
3
GND (0V)
4
Pb signal output
5
GND (0V)
6
Ys signal output
7
GND (0V)
8
Pr signal output
TL7055 PCB Outline
Board Operation: TL7055
TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal. The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes). The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as 7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels. In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode. TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera. When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details). The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055.
Test Pattern Generator (TPG) mode:
TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default. TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards. The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control. The following VISCA commands are available for TPG control (all codes as hex values): TPG activation: 87 01 00 24 01 08 0A FF TPG deactivation: 87 01 00 24 01 08 06 FF TPG pattern type 100% color bar: 87 01 00 24 04 00 04 FF TPG pattern type multi pattern with moving block: 87 01 00 24 04 00 00 FF TPG video standard: 87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50 pq = 19 for 720p60
TL7055 | Production Kit
Partnumber
Content
TL7055
3G-SDI & analog Board
TLCK-B6
1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
3. TLCK-K08-150 8wire cable harness for the analog YsPbPr video output
TL7055-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB-SA
USB to serial adapter
CK-MCX-BNC
MCX to BNC connector cable
Price on request
The AIVION TL8651 outputs serial digital video (SDI) up to 1080p60. It connects to the digital video interface of the block cameras and supports several progressive and interlace HDTV formats.
Features:
One 3G-SDI/HD-SDI Output
Right angle DIN7A connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Board Side Mount
The TL8651 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras.
Tamron MP1010M-VC
Tamron MP1110M-VC
Camera Control
RS232 and TTL level serial control interface
Temperature Range and Power
Operating ambient temperature range -5°C/+60°C
Operating humidity range 20% to 80%
Supply voltage 9.5V to 12V DC regulated
Small form factor & Compliance
Small form factor 60mm x 36mm
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Applications
Industrial, medical, security, inspection, ROV and Security
Download TL8651 Datasheet
TL8651 Block Diagram
Power Input:
9.5V to 12V DC regulated supply input voltage range
Power consumption (MP1110M-VC + TL8651) 4.7W (cam motors inactive)
Power consumption value conditions: Power 12V DC, video mode 1080p60
Ambient temperature +25°C/77°F Humidity 30%
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80%
Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80%
TL8651 PCB Connectors
J2 KEL USL00-30L-A
Camera IF, use supplied 30wire micro coaxial cable only
J4 3G/HD-SDI output
KEL USL00-30L-A
Default type: CEI C-SX113 (DIN7A / 1.0/2.3 coax system)
J3 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC In
2
DC In
3
GND
4
GND
5
Reset / Shut Down, pull to GND to reset/shut down TL7650 and camera for reset, pull to GND for one second or longer
6
GND
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J5 CVBS Output
JST SM03B-SRSS-TB
Pin
Signal
1
GND
2
CVBS analog video output
3
GND (0V)
CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details.
In NTSC or PAL mode, there will be no SDI output signal available from TL8651.
CVBS output connector J5 is available on Rev.B boards from September 26, 2018.
TL8651 PCB Outline
TL8651 | Production Kit
Partnumber
Content
TL8651
3G/HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL8651-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
TL-EVK-DIN-BNC-1
Connector cable with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter
Price on request
The AIVION TL8656 outputs serial digital video (SDI) up to 1080p60 with Power and Control over Coaxial Cable and an external Trigger. It connects to the digital video interface of the block cameras and supports several progressive and interlace HDTV formats.
Features:
One 3G-SDI/HD-SDI Output
Right angle DIN7A connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Board Side Mount
The TL8656 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras.
Tamron MP1010M-VC
Tamron MP1110M-VC
Camera Control
RS232 and TTL level serial control interface
Power and Control over Coaxial Cable
Ext. Trigger
Temperature Range and Power
Operating ambient temperature range -5°C/+60°C
Operating humidity range 20% to 80%
Supply voltage 9.5V to 12V DC regulated
Small form factor & Compliance
Small form factor 60mm x 36mm
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Applications
Industrial, medical, security, inspection, ROV and Security
Download TL8656 Datasheet
TL8656 Block Diagram
Power Input:
9.5V to 12V DC regulated supply input voltage range
Power consumption (MP1110M-VC + TL8656) 4.7W (cam motors inactive)
Power consumption value conditions: Power 12V DC, video mode 1080p60
Ambient temperature +25°C/77°F Humidity 30%
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80%
Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80%
TL8656 PCB Connectors
J2 KEL USL00-30L-A
Camera IF, use supplied 30wire micro coaxial cable only
J4 3G/HD-SDI output
KEL USL00-30L-A
Default type: CEI C-SX113 (DIN7A / 1.0/2.3 coax system)
J3 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC In
2
DC In
3
GND
4
GND
5
Reset / Shut Down, pull to GND to reset/shut down TL7650 and camera for reset, pull to GND for one second or longer
6
GND
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J5 CVBS Output
JST SM03B-SRSS-TB
Pin
Signal
1
GND
2
CVBS analog video output
3
GND (0V)
CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details.
In NTSC or PAL mode, there will be no SDI output signal available from TL8656.
CVBS output connector J5 is available on Rev.B boards from September 26, 2018.
TL8656 PCB Outline
TL8656 | Production Kit
Partnumber
Content
TL8656
3G/HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm Type (1:n)
TL8656-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
TL-EVK-DIN-BNC-1
Connector cable with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter
Price on request