Analog Interfaces
Filter
–
SL4651 is a small form factor HD-TVI/AHD analog HD video transmitter for Block Cameras. Camera LVDS video input signals are demultiplexed, processed and output over a MCX coaxial connector. Camera control is accomplished by a transparent full
duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B-0200 cable kit is included and contains 30wire micro coaxial cable for connecting SL4651
to the camera as well as 10wire power supply and serial control cable harness.
Features:
High Definition analog HD-TVI or AHD output
1080p30 /25 Hz
720p60 /50 Hz
Small form factor
Small form factor 55mm x 36mm
Camera Control
RS232 and TTL level serial control interface
RS485 camera control interface (optional)
Temperature Range and Power
Operating ambient temperature range -10°C to +60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC regulated
Compliance
RoHS compliant
UL/UR compliant
Applications
Full HD integrated cameras with analog HD YPbPr output requirements
Industrial, medical, security, law enforcement
Download SL4651 Datasheet V2.2.0
SL4651 Block Diagram
Power Input:
9V to 12V DC regulated supply input voltage range
Characteristics:
PD = 4.08W (MP1110M-VC camera lens steady +SL4651)
PD = 4.56W (FCB-EV7520A camera lens steady +SL4651)
PSL4651 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%)
Operating and Storage Conditions:
Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4561 is RoHS compliant (2002/05/EG and 2011/65/EU)
SL4651 PCB Connectors
J6 HD-TVI/AHD output connector
Samtec MCX7-J-P-H-RA-TH1
J5 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power & Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND
7
TXD_TTL (serial IF transmit 3.3V, optional)
8
RXD_TTL (serial IF receive 3.3V, optional)
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
SL4651 PCB Outline
Onboard Mode Switch:
Switch #1 SL4651 Video Output Mode: OFF=HD-TVI, ON=AHD
Switch #2 Camera Monitoring Mode Adjust: OFF=No change, ON*=Force 1080p30 *SL4651 onbaord microcontroller adjusts camera video output setting to 1080p30 if switch #2 is in ON position. Checking switch #2 is done once during SL4651
boot cycle. Changing switch #2 position during board operation has no effect. Also switch #1 must be preset before power is applied to SL4651.
SL4651 | Production Kit
Partnumber
Content
SL4651
HD-TVI Board
TLCK-B
1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
SL4651-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
Price on request
SL4655 is a small form factor analog YPbPr FHD video transmitter. Camera LVDS video input signals are demultiplexed, processed, converted to analog and output over 6pin board to wire connector.
Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B5 cable kit is included and contains
30wire micro coaxial cable for connecting SL4655 to the camera as well as 10wire power supply and serial control cable harness and a 6wire cable harness for the video output.
Features:
High Definition analog HD-YPbPr output
1080p30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25 Hz
Small form factor
Small form factor 55mm x 36mm
Camera Control
RS232 and TTL level serial control interface
RS485 camera control interface (optional)
Temperature Range and Power
Operating ambient temperature range -10°C to +60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC regulated
Compliance
RoHS compliant
UL/UR compliant
Applications
Full HD integrated cameras with analog HD YPbPr output requirements
Industrial, medical, security, law enforcement
Download SL4655 Datasheet V1.2.0
SL4655 Block Diagram
Power Input:
9V to 12V DC regulated supply input voltage range
Characteristics:
PD = 4.08W (MP1110M-VC camera lens steady +SL4655)
PD = 4.56W (FCB-EV7520A camera lens steady +SL4655)
P SL4655 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%)
Operating and Storage Conditions:
Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4565 is RoHS compliant (2002/05/EG and 2011/65/EU)
SL4655 PCB Connectors
J5 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power & Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
TXD_TTL (serial IF transmit 3.3V, optional)
8
RXD_TTL (serial IF receive 3.3V, optional)
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
J7 YPbPr Video Output
JST SM6B-SRSS-TB
Pin
Signal
1
Y signal output
2
GND (0V)
3
Pb signal output
4
GND (0V)
5
Pr signal outpu
6
GND (0V)
SL4655 PCB Outline
SL4655 | Production Kit
Partnumber
Content
SL4655
FHD LVDS to analog YPbPr Board
TLCK-B5
1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
3. TLCK-K06-150 6 pin flying leads cable for YPbPr, length 15cm
SL4655-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
Price on request
The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector.
Features:
One 3G-SDI/HD-SDI Output
MCX connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
One Analog YsPbPr Output
8pin board to wire connector Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV Pb, Pr 0,7Vpp into 75 ohms
1080p60 /59.94 /50 /30 /29.97 /25 Hz
720p60 /59.94 /50 Hz
Camera Control
RS232 level serial camera control interface
Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface.
Temperature Range and Power
Operating ambient temperature range -10°C to +60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC regulated
Small form factor & Compliance
Small form factor 46mm x 44mm
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Applications
Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements
Industrial, medical, security, law enforcement
Download TL7055 Datasheet
TL7055 Block Diagram
Power Input:
9V to 12V DC regulated supply input voltage range
Characteristics:
PD = 5.6W (FCB-EV7520A camera lens steady +TL7055)
PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%)
Operating and Storage Conditions:
Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU)
TL7055 PCB Connectors
J8 SDI Video Output
Samtec MCX7-J-P-H-ST-SM1
J7 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J2 Power & Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
Do not connect
8
Do not connect
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
J4 YPbPr Video Output
JST SM08B-SRSS-TB
Pin
Signal
1
HSync
2
VSync
3
GND (0V)
4
Pb signal output
5
GND (0V)
6
Ys signal output
7
GND (0V)
8
Pr signal output
TL7055 PCB Outline
Board Operation: TL7055
TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal. The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes). The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as 7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels. In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode. TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera. When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details). The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055.
Test Pattern Generator (TPG) mode:
TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default. TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards. The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control. The following VISCA commands are available for TPG control (all codes as hex values): TPG activation: 87 01 00 24 01 08 0A FF TPG deactivation: 87 01 00 24 01 08 06 FF TPG pattern type 100% color bar: 87 01 00 24 04 00 04 FF TPG pattern type multi pattern with moving block: 87 01 00 24 04 00 00 FF TPG video standard: 87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50 pq = 19 for 720p60
TL7055 | Production Kit
Partnumber
Content
TL7055
3G-SDI & analog Board
TLCK-B6
1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
3. TLCK-K08-150 8wire cable harness for the analog YsPbPr video output
TL7055-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB-SA
USB to serial adapter
CK-MCX-BNC
MCX to BNC connector cable
Price on request
The TL9801 CVBS analog video interface from AIVION is a small form factor module to convert LVDS.
Features:
CVBS analog video output
CVBS pass through from camera. Camera must be set to CVBS PAL or NTSC operating mode.
Small form factor
Small form factor 44mm x 38mm
Camera Control
USB2 UART based camera control
Power
9V to 12V DC regulated
Compliance
RoHS compliant
UL/UR compliant
Temperature Range
Operating ambient temperature range -5°C/+60°C
Operating humidity range 20% to 80%
Download TL9801 Datasheet V1.0.0
TL9801 Block Diagram
Power Input:
9V TO 12V regulated
Power consumption (MP1110M-VC + TL9801) 3.2 W (cam motors inactive)
Operating and Storage Conditions:
Operating: Ambient Temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
Storage: Ambient Temperature (min/max): -20°C/+60°C = -4°F/140°FHumidity: 20%-80%
TL9801 PCB Connectors
J1 DC Jack
Fitting plug inner/outer diameter: 2.55mm/5,5mm
Center Pin DC Power Input - Shield GND
J2 USB2 micro connector
USB2 UART camera control interface
USB2 UART chip Cypress CY7C65213
J5 MCX Coaxial connector
Primary CVBS Output
J9 Micro coaxial connector
J6 CVBS Output (Board to wire connector)
JST BM08B-SSRS-TB
Pin
Signal
1
CVBS Output (alternative to J5, do not connect both)
2
GND
3
Do not connect
4
Do not connect
5
Do not connect
6
GND (0V)
7
Do not connect
8
Do not connect
TL9801 PCB Outline
TL9801 | Production Kit
Partnumber
Content
TL9801
CVBS Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm (Type 1:n)
TL9801-EXT | Evaluation Extension
Partnumber
Content
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
CK-MCX-BNC
MCX to BNC connector cable
Price on request