NA1012B-ET | HDMI TO 3G/HD-SDI CONVERTER (board to board connector)

EK-PA1131 For test and evaluation purposes adaptor EK-PA-1131 is available. It provides a HDMI A-type connector for video input as well as USB2 connector which can be used to supply 5V DC power to NA1012B-ET. In addition it allows easy access to the debug/status port by an USB2 UART.

The NanoConverter NA1011 from AIVION is part of a family of small form factor solutions for transmitting and receiving standard based video signals over different physical media such as coaxial cables and optical fibre. Different video formats and interface standards are supported from the transmitter and receiver side including DVI, HDMI, CVBS, YPbPr, RGB, 3G-SDI, HD-SDI and SD-SDI. Features One 3G-SDI/HD-SDI Input 75 Ohm MCX jacks connector. Supporting bit rates due to SMPTE292M and SMPTE424M (level A) 1.485 Gbps 1.485/1.001 Gbps 2.97 Gbps 2.97/1.001 Gbps One SDI loop out with reclocking 75Ohm MCX jacks connector. One HDMI output 19 pin HDMI connector. Compliant to HDMI 1.3 No HDCP support Output Data format RGB444, 3x10 bit Extendet Temperature Range -25°C to +70°C (-13°F to 158°F), Humidity 20% to 70% Small form factor PCB dimensions 38mm x 38mm Native video signal processing No image scaling, no format conversion. Download NA1011-ET Datasheet NA1011-ET Block Diagram Operating Range -25°C to +70°C (-13°F to 158°F), Humidity 20% to 70% Vin (DC) min typ max 5V 12V 18V Input Current Requirements At 25°C ambient temperature Vin 3G Operation HD Operation Condition 5V 510mA 450mA Shutdown = Vin or OPEN 12V 220mA 200mA Shutdown = Vin or OPEN 18V 160mA 145mA Shutdown = Vin or OPEN 5-18V < 10mA < 10mA Shutdown = GND NA1011-ET PCB Connectors J3 HDMI Output Connector Samtec HDMR-19-02-F-SM-PF Pin assignment due to HDMI standard J2 (In)/ J7 (Out) 3G-SDI and HD-SDI Connectors MCX 75Ohm The NA1011-ET has straight MCX connectors. Right angled MCX connectors are optional available. J1 Power Connector JST SM03B-SRSS-TB Pin Signal 1 Vin DC input, 5V to 18V 2 Shutdown/Reset, has pull up resistor of 4,7kOhm to Vin 3 GND (0V) J4 Serial Control Interface JST SM08B-SRSS-TB Pin Signal 1 reserved, do not connect 2 reserved, do not connect 3 reserved, do not connect 4 GND 5 RX data (host to device), 3.3V TTL, 4V max. 6 TX data (host to device), 3.3V TTL, 4V max. 7 GND 8 reserved, do not connect NA1011-ET PCB Outline Notes NA1011-ET The Nanoconverter products are RoHS, REACH and UL/UR compliant. The device detects and measures video input parameter and adjusts all necessary settings accordingly. Manual control is not required. However, the serial control interface can be used for status checking. Any terminal software can be used, whereas parameters have to be set to 38400bps, 8 data bits, no parity and 1 stop bit (8N1). No handshake must be used The current device version does not support audio. The device version does not process HDCP encrypted HDMI input signals. NA1011-ET | Production Kit Partnumber Content NA1011-ET Converter with straight MCX connectors TLCK-FL03-150 3pin flying leads cable for power, lead length = 15cm / 5.9inch 

The NanoConverter NA1012-ET from AIVION is part of a family of small form factor solutions for transmitting and receiving standard based video signals over different physical media such as coaxial cables and optical fibre. Different video formats and interface standards are supported from the transmitter and receiver side including DVI, HDMI, CVBS, YPbPr, RGB, 3G-SDI, HD-SDI and SD-SDI. Features One HDMI input 19 pin HDMI Connector. Compliant to HDMI 1.4a and DVI 1.0.Input format support: RGB 444 YCbCr 444 YCbCr 422 Two SDI outputs 75 ohm MCX jacks connector. Supporting bit rates due to SMPTE292M and SMPTE424M 1.485 Gbps 1.485/1.001 Gbps 2.97 Gbps 2.97/1.001 Gbps Full-HD Support Supported Video formats: 1080p at 50/25/24/59.94/29.97/23.98/60/30 1080i at 50/59.94/60 720p at 50/ 59.94/60 Extendet Temperature Range -25°C to +70°C (-13°F to 158°F), Humidity 20% to 70% Small form factor PCB dimensions 38mm x 38mm Native video signal processing No image scaling, no format conversion. Download NA1012-ET Datasheet NA1012-ET Block Diagram J2 HDMI Input Connector Samtec HDMR-19-02-F-SM-PF Pin assignment due to HDMI standard J5 / J6 3G-SDI and HD-SDI Output Connectors MCX 75Ohm J1 Power Connector JST SM03B-SRSS-TB Pin Signal 1 Vin DC input, 5V to 18V 2 Shutdown/Reset, has pull up resistor of 4,7kOhm to Vin 3 GND (0V) J3 Serial Control Interface JST SM08B-SRSS-TB Pin Signal 1 reserved, do not connect 2 reserved, do not connect 3 reserved, do not connect 4 GND 5 RX data (host to device), 3.3V TTL, 4V max. 6 TX data (host to device), 3.3V TTL, 4V max. 7 GND 8 reserved, do not connect NA1012-ET PCB Outline Notes NA1012-ET The Nanoconverter products are RoHS, REACH and UL/UR compliant. The NA1012 converts video signals received from a DVI or HDMI source for transmission over an 3G/HD- SDI interface which requires clock signals to be in a well defined range. This might not be the case when standard HDMI or DVI output of desktop computers, laptop computers ot other consumer devices are used as signal source. The HDMI/DVI TMDS input clock requirements are: 3G mode: 148.5MHz or 148.5 MHz/1.001 +/- 60ppm HD mode: 74.25MHz or 74.25MHz/1.001 +/- 80 ppm The device detects and measures video input parameter and adjusts all necessary settings accordingly. Manual control is not required. However, the serial control interface can be used for status checking. Any terminal software can be used, whereas parameters have to be set to 38400bps, 8 data bits, no parity and 1 stop bit (8N1). No handshake must be used. The current device version does not support audio. The device version does not process HDCP encrypted HDMI input signals. NA1012-ET | Production Kit Partnumber Content NA1012-ET Converter with straight MCX connectors TLCK-FL03-150 3pin flying leads cable for power, lead length = 15cm / 5.9inch