Filter
–
Kit:
Production Kit (Board incl. Cable)
|
Block Cameras:
No Block Camera
The TL3K7052 is a WQHD HDMI output video transmitter for block cameras from AIVION. It connects to the digital video interface of the block cameras and support several progressive and interlace HDTV formats.
Features:
One HDMI Output
1440p30 /25 Hz
1080p30 /25 Hz
720p30 /25Hz
Small Form Factor
Small form factor 46mm x 44mm
Camera Control
RS232 level serial camera control interface
TTL level serial control interfac
Temperature Range
Ambient temperature (min/max): -5°C/+60°C
Operating humidity range 20% to 80%
Temperature monitoring with alert function
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Power
9V to 12V DC regulated (13V DC absolute maximum)
Download TL3K7052 V1.0.0 Datasheet
TL3K7052 Block Diagram
Power Input:
9V to 12V DC regulated (13V DC absolute maximum)
Power consumption (incl. camera) 5.3W (cam motors inactive)
Characteristics:
PD = 5.6W (FCB-EV7520A camera lens steady +TL7055)
PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/140°F - Humidity: 20%-80%
TL3K7052 PCB Connectors
J3 LVDS Video In
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J8 HDMI Camera Interface
Kycon KDMIX_FS1V_WS or equivalent
J1 Power and RS232/TTL Control IF
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera for reset, pull to GND for one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
TL3K7052 PCB Outline
Test Pattern Generator
TL3K7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL3K7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL3K7052 power off and on again
Note: For TPG operation on TL3K7052, the camera must be connected.
TL3K7052 | Production Kit
Partnumber
Content
TL3K7052
WQHD HDMI Board
TLCK-B
1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL3K7052-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
TL-EVK-BRA
Bracket and screws
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
Price on request
Kit:
Production Kit (Board incl. Cable)
|
Block Cameras:
No Block Camera
The TL4K1152 is a small form factor digital serial video transmitter from AIVION. Small form factor with an attractive price are some of the main features of the TL4K1152. It supports the new trend setting Sony block camera FCB 4K Series from Sony via an HDMI output. Camera control can be managed through an RS232 port. Via the available USB2 interface firmware updates can be obtained.
Features:
One HDMI 1.4b video output
Up to 2160p30
UHD, FHD, HD video format support
Integrated input signal equalizer
Ultra high speed 3.4Gbps cable driver
Small Form Factor
Small form factor 46mm x 30mm
Camera Control
RS232 level serial camera control interface
3.3V TTL level serial camera control IF
Temperature Range
Ambient temperature (min/max): -5°C/+60°C
Operating humidity range 20% to 80%
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
Power
Supply voltage 7V to 12V DC regulated
Ultra low power - 150mW@8V supply voltage only
Download TL4K1152 V2.0.0 Datasheet
TL4K1152 Block Diagram
Power Input:
7V to 12V DC regulated supply input voltage range
Characteristics:
PD = 3.05W (FCB-ER8300 lens steady +TL4K1152)
PTL4K1152 = 150mW (typ.) (8V DC supply, 3840x2160@29.97fps, TA = 25°C, Humididty = 40%)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
TL4K1152 PCB Connectors
J4 LVDS Video In
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J2 HDMI Camera Interface
J1 Power and RS232/TTL Control IF
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
TXD_TTL (serial IF transmit 3.3V)
8
RXD_TTL (serial IF receive 3.3V)
9
RXD_232 (serial IF receive RS232)
10
TXD_232 (serial IF transmit RS232)
J3 USB connector
do not connect (for FCB-ER8300 firmware updates only). USB connector is no more assembled for revision B boards.
TL4K1152 PCB Outline
TL4K1152 | Production Kit
Partnumber
Content
TL4K1152
HDMI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL4K1152-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
TL-EVK-BRA
Bracket and screws
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
Price on request
Kit:
Production Kit (Board incl. Cable)
|
Block Cameras:
No Block Camera
The TL7050 Dual 3G/HD-SDI and DVI(HDMI) Output Video Transceiver module from AIVION connect to the
digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV
formats. As no analog to digital conversion is done on these modules, excellent output image quality is
achieved.
Features:
Dual 3G-SDI/HD-SDI Output
3G-SDI output compliant to SMPTE 424M level A
HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
One HDMI Output
HDMI connector (Kycon KDMIX_FS1V_WS)
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Robust RS485 differential serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Video input and Compliance
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7050 V 2.5.0 Datasheet
TL7050 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Characteristics:
Power consumption TL7050: 260mA @ 12V DC (typ.)
Operating and Storage Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7050 PCB Connectors
J8 HDMI connector
Kycon KDMIX_FS1V_WS
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera. For reset, pull to GND for
one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J2 RS485 Control IF
JST SM08B-SRSS-TB
Pin
Signal
1
TXD_P (to controller)
2
TXD_N (to controller)
3
RXD_N (from controller)
4
RXD_P (from controller)
5
GND
6
3.45V typ. (max. current 50mA)
J5 Analog component YPbPr and CVBS output
Requires TL7050 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output
TL7050 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V)
- In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7050 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7050 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7050 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7050
Analog Video Output
TL7050 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera.
In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation.
Reset Operation
When applying power to TL7050, the camera is also automatically powered. During power up all functions on TL7050, are reset and initialized.
During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7050. The interface is passed through to the camera that all VISCA protocol based software can be used.
Serial interface selection must be done be appropriate setting of switch-2.
TL7050 | Production Kit
Partnumber
Content
TL7050
HDMI-HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL7050-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
CK-MCX-BNC
MCX to BNC connector cable
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
Price on request
Kit:
Production Kit (Board incl. Cable)
|
Block Cameras:
No Block Camera
The TL7052 DVI(HDMI) Output Video Transceiver module from AIVION connects to the
digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV
formats. As no analog to digital conversion is done on these modules, excellent output image quality is
achieved.
Features:
Video input
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
One HDMI Output
HDMI connector (Kycon KDMIX_FS1V_WS)
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7052 V 2.4.0 Datasheet
TL7052 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Operating Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7052 PCB Connectors
J8 HDMI connector
Kycon KDMIX_FS1V_WS
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7052 and camera. For reset, pull to GND for
one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J5 Analog component YPbPr and CVBS output
Requires TL7052 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
J4 24pin FFC Connector
Power, Reset, Serial Control IF, analog Video
TL7052 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V)
- In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7052 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7052
Analog Video Output
TL7052 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera.
In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation.
Reset Operation
When applying power to TL7052, the camera is also automatically powered. During power up all functions on TL7052, are reset and initialized.
During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7052. The interface is passed through to the camera that all VISCA protocol based software can be used.
Serial interface selection must be done be appropriate setting of switch-2.
TL7052 | Production Kit
Partnumber
Content
TL7052
HDMI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL7052-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
Price on request
Kit:
Production Kit (Board incl. Cable)
|
Block Cameras:
No Block Camera
The TL8652 HDMI Output Video Transceiver module from AIVION connect to the digital video interface of the block cameras and support several progressive and interlace HDTV formats. TL8652 outputs HDMI up to 1080p60.
Features:
HDMI 1.4 output
RGB444 or YCbCr422 colour format selectable
1080p60 /50 /30 /25 Hz
1080i60 /50 Hz
720p60 /50 Hz
Board Side Mount
The TL8652 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras.
Tamron MP1010M-VC
Tamron MP1110M-VC
Camera Control
RS232 and TTL level serial control interface
Integrated USB2 UART for camera control
Temperature Range
Operating ambient temperature range -5°C/+60°C
Operating humidity range 20% to 80%
Small form factor & Compliance
Small form factor 61mm x41mm
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Power
USB powered 5V DC
Download TL8652 V2.2.0 Datasheet
TL8652 Block Diagram
Power Input:
5V DC over USB2 micro connector (USB3 host port or powered USB3 hub required)
Power consumption (MP1010M-VC + TL8652) 4.5W/900mA (cam motors inactive)
Power consumption TL8652: 1.5W, 300mA @ 5V DC (typ.)
Ambient temperature +25°C/77°F Humidity 30%
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80%
Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80%
TL8652 PCB Connectors
J6 KEL USL00-30L-A
Camera IF, use supplied 30wire micro coaxial cable only
J3 HDMI micro connector
J2 USB2 micro connector
J1 Reset and RS232 Control IF
JST SM10B-SRSS-TB
Pin
Signal
1
Do not connect
2
Do not connect
3
GND
4
GND
5
Reset / Shut Down, pull to GND to reset/shut down TL8652 and camera for reset, pull to GND for one second or longer
6
GND
7
Do not connect
8
Do not connect
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J7 CVBS Output
JST SM03B-SRSS-TB
Pin
Signal
1
GND
2
CVBS analog video output
3
GND (0V)
CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details.
In NTSC or PAL mode, there will be no HDMI output signal available from TL8652/A.
TL8652 PCB Outline
TL8652 | Production Kit
Partnumber
Content
TL8652
HDMI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL8652-EXT | Evaluation Extension
Partnumber
Content
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
Driver Installer Package and
Cypress USB-Serial Driver Installation Guide for the USB2 UART Chip are online available.
TL-EVK-HDMI-MICRO-D
High Speed HDMI Cable 1 with HDMI-A 19 and 1 HDMI Micro-D 19 pin male connector
Price on request