There are several requirements for video systems in the medical market. In general this market is asking for video systems that do not add artifacts to the video image. For that reason our interfaces and transmission systems are using uncompressed video. Our solutions are usually used in three different fields of applications:
Surgery Lamps
In more and more hospitals it becomes a standard to have surgery lamps that offer embedded video systems to allow documentation and monitoring. Usually, block cameras are preferred since they do allow zoom and autofocus in combination with a small form factor.
Depending on the position of the Monitor we offer HDMI or SDI based transmission technology. Using our interfaces and converters it’s possible to mix those standards and use the SDI technology to bridge a long distance from the Camera to the Monitor and convert this SDI signal into HDMI to enable the usage of standard HDMI Monitors.
Dermatology
If the human skin should be observed a computing unit usually is postprocessing the video stream. Nevertheless, that video must not have any compression artefacts since those artefacts could generate wrong results. We are using uncompressed video together with a USB3 interface (UVC). Connecting a small block camera to our USB3 interfaces allows to display or postprocess the video with a computer.
Systems for visually handicapped persons
To support visually handicapped persons zoom camera blocks with good zoom lenses and fast autofocus capabilities are a good choice. Also here it is important that the camera system is providing video with low latency since it simplifies the usage to position the text under the lens. Video systems that are directly connected to a Monitor are using very often HDMI connectors.
The TL4K1152 is a small form factor digital serial video transmitter from AIVION. Small form factor with an attractive price are some of the main features of the TL4K1152. It supports the new trend setting Sony block camera FCB 4K Series from Sony via an HDMI output. Camera control can be managed through an RS232 port. Via the available USB2 interface firmware updates can be obtained.
Features:
One HDMI 1.4b video output
Up to 2160p30
UHD, FHD, HD video format support
Integrated input signal equalizer
Ultra high speed 3.4Gbps cable driver
Small Form Factor
Small form factor 46mm x 30mm
Camera Control
RS232 level serial camera control interface
3.3V TTL level serial camera control IF
Temperature Range
Ambient temperature (min/max): -5°C/+60°C
Operating humidity range 20% to 80%
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
Power
Supply voltage 7V to 12V DC regulated
Ultra low power - 150mW@8V supply voltage only
Download TL4K1152 V2.0.0 Datasheet
TL4K1152 Block Diagram
Power Input:
7V to 12V DC regulated supply input voltage range
Characteristics:
PD = 3.05W (FCB-ER8300 lens steady +TL4K1152)
PTL4K1152 = 150mW (typ.) (8V DC supply, 3840x2160@29.97fps, TA = 25°C, Humididty = 40%)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
TL4K1152 PCB Connectors
J4 LVDS Video In
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J2 HDMI Camera Interface
J1 Power and RS232/TTL Control IF
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
TXD_TTL (serial IF transmit 3.3V)
8
RXD_TTL (serial IF receive 3.3V)
9
RXD_232 (serial IF receive RS232)
10
TXD_232 (serial IF transmit RS232)
J3 USB connector
do not connect (for FCB-ER8300 firmware updates only). USB connector is no more assembled for revision B boards.
TL4K1152 PCB Outline
TL4K1152 | Production Kit
Partnumber
Content
TL4K1152
HDMI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL4K1152-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
TL-EVK-BRA
Bracket and screws
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
The TL4K1171 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed, and output over coaxial connectors. 6G-SDI output is compliant to SMPTE ST2081-10 MODE 1 mapping, Dual
Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping and 3G-SDI FHD output is compliant to SMPTE ST425-1 level A standards. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between
camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B cable kit is available as accessory.
Features:
SDI Video Output
Native signal processing for highest image quality
MCX 75 Ohm straight coaxial connectors
Resolution up to 3840x2160p @ 30fps
6G-SDI output of UHD formats
Dual Link 3G-SDI output of UHD formats
3G-SDI output of FHD formats
Automatic format detection
Small Form Factor
Small form factor 60mm x 46mm
Camera Control
RS232 level serial camera control interface
3.3V TTL level serial camera control interface
Temperature Range and Power
Ambient temperature (min/max): -5°C/+60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Application
4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530, FCB-ER8300, FCB-ES8230 and FCB-EW9500H camera blocks
Industrial, medical, security, law enforcement, video production
Download TL4K1171 V1.0.1 Datasheet
TL4K1171 Block Diagram
Power Input:
9V to 12V DC (12.5V DC max.) regulated supply input voltage range
Characteristics:
PD = 7.0W typ. (FCB-ER8530 lens steady +TL4K1171)
P TL4K1171 = 3.9W (typ.) (12V DC supply, 3840x2160@29.97fps, TA = 25°C, Humididty = 40%)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
TL4K1171 PCB Connectors
J1 Power and Control IF
(JST SM10B-SRSS-TB)
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
TXD_TTL (serial IF transmit 3.3V, optional)
8
RXD_TTL (serial IF receive 3.3V, optional)
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
J3 External Sync
(JST SM08B-SRSS-TB) for use with FCB-ER8550 only
Pin
Signal
1
GND (0V)
2
External Sync Loop Out
3
GND (0V)
4
ACC_LED (Output signal from FCB-ER8550)
5
GND (0V)
6
External Sync Input
7
GND (0V)
8
SYNC_LOCK (Output signal from FCB-ER8550)
J4 HDMI Input
(KEL USL00-30L-A)
30wire microcoax connector for FCB-ER8xxx and FCB-EW9500H. Use 30wire micro coaxial cable supplied with cable kit.
J6 Board feature extension connector
Contact us for further notice
J7 + J8 SDI output connector
(Samtec MCX7-J-P-H-ST-TH1)
Mode
J7
J8
UHD 6GbpsUHD mode selection by switch#2
No output
6G-SDI
UHD 3GbpsUHD mode selection by switch#2
Link1 of Dual Link 3G-SDI
Link2 of Dual Link 3G-SDI
FHDFHD operation requires camera to be set to 1080p60, 1080p59.94 or 1080p50
GND (0V)
3G-SDI (same signal as J7)
Board Config Switch
Switch#
OFF
ON
1
RS232 based camera control
3.3V TTL based camera control
2
6G-SDI UHD Output Mode
DL 3G-SDI UHD Output Mode
3
Keep OFF
Reserved
4
Keep OFF
Reserved
TL4K1171 PCB Outline
TL4K1171 | Production Kit
Partnumber
Content
TL4K1171
6 Gbps / Dual Link 3Gbps UHD-SDI Interface Board
TLCK-B
1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL4K1171-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
2 x CK-MCX-BNC
MCX to BNC connector cable
The FCB-EV7520 camera block incorporates a 1/2.8-type Exmor RTM CMOS sensor, providing Full-HD video with extraordinary sensitivity. In addition, the Sony block camera includes STARVISTM technology to realize high picture
quality in visible light and near-infrared light. With 30x optical zoom and either HD or Full-HD capability, the camera inherits a multitude of Sony’s FCB features, including Auto ICR, Spherical Privacy Zone Masking,
and Defog.
Sony FCB-EV7520 Features
30x Enhanced Optical Zoom
Digital Zoom 12x (360x with optical zoom)
Full HD (1080p/60)
Image Sensor 1/2.8-type Exmor R CMOS
Minimum illumination Colour: 0.01 lx (F1.6,AGC on, 1/30 s)
Defog · High Light Compensation · Wide Dynamic Range
Super Image Stabilizer
Auto IR-cut Filter Removal
Spehrical privacy zone masking
Noise reduction
Slow AE response
Datasheet Sony FCB-7520 Series
Overview Features FCB-EV7520
Capture crisp, clear Full-HD (1080/60p)
Even in low-light environments, the high-performance 1/2.8-type Exmor CMOS image sensor achieves outstanding Full-HD (1920 x 1080) picture quality. Progressive scanning assures smoother pictures with reduced blur – ideal for capturing
the detail in moving images.
Get a steadier picture with the image stabilizer.
The camera's built-in image stabilizer function counters the effect of blurred, shaky images caused by low-frequency vibration. It is helpful for outdoor surveillance and traffic monitoring applications, mainly if the camera is used
on a bridge or mounting pole where it is subjected to wind or mechanical vibration.
Stable Zoom
Image stabilizer and optical/digital zoom are combined to improve image quality while maintaining the original horizontal viewing angle. This does not affect the image size and reduces blu.
2D/3D noise reduction
Advanced noise reduction technology filters noise from the image for clearer results, especially in low-light conditions. Noise reduction can be selected from five levels to suit a wide range of operating environments.
Wide dynamic range
Wide-D image processing technology allows one to see clear, detailed images in high-contrast or backlit environments. Models now support an extensive 130 dB dynamic range activated via the VISCA command.
De-fog
The de-fog feature allows more precise and natural viewing in foggy or misty scenes. The camera detects the haze level and automatically applies the required effects when this feature is activated. Depending on user requirements, the
level of these effects can be adjusted via the VISCA command.
HLC (High Light Compensation)
HLC technology helps to improve, for example, the visibility of license plates when bright headlights are shot under low-light conditions. The bright parts in the image are masked and compensated automatically to achieve better visibility.
Auto ICR (Auto IR-cut Filter Removal)
In low-light conditions, the camera automatically switches from Day to Night mode, removing the IR-cut filter to boost sensitivity for clear pictures in near-darkness. The spherical privacy zone masking feature enables areas of view
to be selectively masked for privacy. Masked areas are automatically interlocked with the camera’s pan/tilt/zoom movements.
Privacy Zone Masking
Privacy Zone Masking protects private objects and areas such as house windows, entrances, and exits within the camera’s range of vision but is not subject to surveillance. Privacy zones can be masked on the monitor to protect privacy.
Wide range of features for versatile operation
Versatile operation is ensured by a wide range of functions and adjustments, including White Balance modes; Picture effects (E-Flip, Nega Art, Black & White, Mirror Image, Colour Enhancement); Motion Detection/Alarm; Picture freeze;
Temperature readout; Slow AE response; Electronic shutter/ slow shutter; and Title display/Camera mode display (English).
Sony FCB-EV7520 Specifications
Feature
Sony FCB-EV7520
Image sensor
1/2.8-type Exmor R CMOS
Image sensor (Number of effective pixels)
Approx.2.13 Megapixels
Signal system
1080p/59.94,1080p/50, 1080p/60, 1080p/30, 1080p/29.97, 1080p/25, 1080i/59.94, 1080i/50, 1080i/60, 1080i/30, 720p/59.94, 720p/50, 720p/60, 720p/30, 720p/29.97, 720p/25, NTSC, PAL
Minimum illumination (50%) High sensitivity mode
Colour: 0.01 lx (F1.6, AGC on, 1/30s)
Minimum illumination (50%) Normal mode
Colour: 0.1 lx (F1.6, AGC on, 1/30s)
S/N ratio
More than 50 dB
Gain Auto/Manual
Auto/Manual 0 dB to 50.0dB (0 to 28 steps +2 step/ total 15 steps)
Gain Max. Gain Limit
Max. Gain Limit 10.7 dB to 50.0 dB (6 to 28 steps +2 tep/ total 12 steps)
Shutter speed
1/1 s to 1/10,000 s, 22 steps
Sync system
Internal
Exposure control
Auto, Manual, Priority mode (shutter priority & iris priority), Bright, EV compensation, Slow AE
Backlight compensation
Yes
Aperture control
16 steps
White balance
Auto, ATW, Indoor, Outdoor, Outdoor Auto, Sodium Vapor Lamp (Fix/Auto/Outdoor Auto), One-push, Manual
Lens
30x optical zoom f = 4.3 mm (wide) to 129.0 mm (tele) F1.6 to F4.7
Digital zoom
12x (360x with optical zoom)
Focusing system
Auto (Sensitivity: normal, low), One-push AF, Manual, Interval AF, Zoom Trigger AF, Focus compensation in ICR on
Horizontal viewing angle 1080p mode
63.7° (wide end) to 2.3° (tele end)
Horizontal viewing angle 720p mode
63.7° (wide end) to 2.3° (tele end)
Horizontal viewing angle SD
47.8° (wide end) to 1.7° (tele end)
Minimum object distance
10 mm (wide end) to 1200 mm (tele end) (Default: 300 mm)
Auto ICR
Yes
Wide-D
Yes (120 dB)
Visibility Enhancer
Yes
De-fog
Yes
HLC
Yes
Noise reduction
Yes (6 steps)
Image stabilization
Yes
StableZoom
Yes
Spherical privacy zone masking
Yes
Motion detection
Yes
Alarm
Yes
Slow AE response
Yes
Picture effects
E-Flip, Nega Art, Black & White, Mirror image, Colour enhancement
Picture freeze
Yes
Slow shutter
Yes
Temperature readout
Yes
Title display
Yes
Camera mode display
20 characters/line, max. 11 lines
Key switch control
Yes
Camera operation switch
Yes
Video output HD Analog
N/A
Video output HD Digital
Digital:Y/Cb/Cr 4:2:2 via LVDS (Signal format conforms to SMPTE 274/SMPTE 296.)
Video output SD
VBS
Camera control interface
VISCA (CMOS 5 V level) Baud rate: 9.6 Kbps, 19.2 Kbps, 38.4 Kbps, 115.2 Kbps, Stop bit: 1 bit
Power requirements
6.0 V to 12.0 V DC
Power consumption - Focus inactive
3.2 W (zoom/focus inactive)
Power consumption - Focus active
4.0 W (zoom/focus active)
Operating temperature
-5°C to +60°C (23°F to 140°F)
Storage temperature
-20°C to +60°C (-4°F to 140 °F)
Operating humidity
20% to 80%, Absolute humidity: 36 g/m3
Storage humidity
20% to 95%, Absolute humidity: 36 g/m3
Dimensions (W x H x D)
50.0 x 60.0 x 89.7 mm (2 x 2 3/8 x 3 5/8 inches)
Mass
255 g (9.0 oz)
Sony FCB-7520 Dimensions
Sony FCB-EV7520 Front
Sony FCB-EV7520 Rear
Sony FCB-EV7520 Top
Sony FCB-EV7520 Bottom
Sony FCB-EV7520 Left
Sony FCB-EV7520 Right
The TL7050 Dual 3G/HD-SDI and DVI(HDMI) Output Video Transceiver module from AIVION connect to the
digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV
formats. As no analog to digital conversion is done on these modules, excellent output image quality is
achieved.
Features:
Dual 3G-SDI/HD-SDI Output
3G-SDI output compliant to SMPTE 424M level A
HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
One HDMI Output
HDMI connector (Kycon KDMIX_FS1V_WS)
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Robust RS485 differential serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Video input and Compliance
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7050 V 2.5.0 Datasheet
TL7050 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Characteristics:
Power consumption TL7050: 260mA @ 12V DC (typ.)
Operating and Storage Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7050 PCB Connectors
J8 HDMI connector
Kycon KDMIX_FS1V_WS
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera. For reset, pull to GND for
one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J2 RS485 Control IF
JST SM08B-SRSS-TB
Pin
Signal
1
TXD_P (to controller)
2
TXD_N (to controller)
3
RXD_N (from controller)
4
RXD_P (from controller)
5
GND
6
3.45V typ. (max. current 50mA)
J5 Analog component YPbPr and CVBS output
Requires TL7050 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output
TL7050 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V)
- In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7050 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7050 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7050 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7050
Analog Video Output
TL7050 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera.
In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation.
Reset Operation
When applying power to TL7050, the camera is also automatically powered. During power up all functions on TL7050, are reset and initialized.
During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7050. The interface is passed through to the camera that all VISCA protocol based software can be used.
Serial interface selection must be done be appropriate setting of switch-2.
TL7050 | Production Kit
Partnumber
Content
TL7050
HDMI-HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL7050-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
CK-MCX-BNC
MCX to BNC connector cable
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
The TL7051 Dual 3G/HD-SDI Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and supports several progressive and interlace HDTV formats. As no analog to digital conversion is done on
these modules, excellent output image quality is achieved.
Features:
Dual 3G-SDI/HD-SDI Output
3G-SDI output compliant to SMPTE 424M level A
HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Video input
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Robust RS485 differential serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7051 Revision D V.3.0.0 Datasheet
TL7051 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Operating Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7051 PCB Connectors
J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7051 and camera. For reset, pull to GND for one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J2 RS485 Control IF
JST SM08B-SRSS-TB
Pin
Signal
1
TXD_P (to controller)
2
TXD_N (to controller)
3
RXD_N (from controller)
4
RXD_P (from controller)
5
GND
6
3.45V typ. (max. current 50mA)
J5 Analog component YPbPr and CVBS output
Requires TL7051 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
TL7051 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (
<
0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7051 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7051 board. In addition one out of two
test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7051 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7051
Analog Video Output
TL7051 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related
camera documentation.
Reset Operation
When applying power to TL7051, the camera is also automatically powered. During power up all functions on TL7051, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND).
This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7051. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection
must be done be appropriate setting of switch-2.
TL7051 | Production Kit
Partnumber
Content
TL7051
3G-SDI/HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL7051-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
CK-MCX-BNC
MCX to BNC connector cable
The TL7052 DVI(HDMI) Output Video Transceiver module from AIVION connects to the
digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV
formats. As no analog to digital conversion is done on these modules, excellent output image quality is
achieved.
Features:
Video input
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
One HDMI Output
HDMI connector (Kycon KDMIX_FS1V_WS)
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7052 V 2.4.0 Datasheet
TL7052 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Operating Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7052 PCB Connectors
J8 HDMI connector
Kycon KDMIX_FS1V_WS
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7052 and camera. For reset, pull to GND for
one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J5 Analog component YPbPr and CVBS output
Requires TL7052 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
J4 24pin FFC Connector
Power, Reset, Serial Control IF, analog Video
TL7052 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V)
- In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7052 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7052
Analog Video Output
TL7052 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera.
In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation.
Reset Operation
When applying power to TL7052, the camera is also automatically powered. During power up all functions on TL7052, are reset and initialized.
During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7052. The interface is passed through to the camera that all VISCA protocol based software can be used.
Serial interface selection must be done be appropriate setting of switch-2.
TL7052 | Production Kit
Partnumber
Content
TL7052
HDMI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL7052-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
The TL6032 interface is a HDTV USB 3.0 compliant video streaming capture solution from AIVION. As no analog to digital conversion is done on these modules, excellent output image quality is guaranteed.
Features:
USB 3.0 Video Output
Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format
1920x1080p @ 25Hz, 29.97Hz, 30 Hz
1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz
The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer
Small Form Factor
Small form factor 45mm x 40mm
USB
Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported)
Host computer must run a UVC capable operating system
Parallel up- and downstream of camera control and status data is possible (USB CDC)
Power
Full USB bus powered camera solution possible depending on camera
Power supply voltage for camera is generated onboard
Allows an external power supply
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Temperature Range
Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Download TL6032 V2.0.0 Datasheet
TL6032 Block Diagram
Power Input:
5V DC from USB3 port
Characteristics:
Power consumption (FCB-EV75xx + TL6035) 5.6W
Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive)
Power consumption TL6035: 2.7W/540mA@5V DC (max.)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80%
TL6032 PCB Connectors
J6 USB3 microB connector
Horizontal
J2 LVDS Video In
30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit.
J7 External Power Supply
Pin
Signal
1
Input voltage 5V to 7V DC
2
Input voltage 5V to 7V DC
3
System reset, pull to GND for reset
4
GND (0V)
5
GND (0V)
J9 RS232 UART Connector
Pin
Signal
1 to 7
do not connect
8
GND
9
RXD (host to camera)
10
TXD (camera to host)
TL6032 PCB Outline
Camera Power
Camera supply voltage is generated on TL6032 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera.
NOTE:
USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6032.
TL6032 EXTERNAL POWER OPTION:
TL6032 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6032 for the camera supply boost converter only. All other electronic devices on TL6032 are always powered from USB3 port. No adjustments on TL6032 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power.
Host (PC) - Device Communication
TL6032 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6032 via a serial communication channel (USB UART).
Connecting the TL6032 to the Host PC
Operating System Support
TL6032 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems:
Windows 7 (32 and 64bit)
Windows 8.1 (32 and 64bit)
Windows 10 (64bit, version 1511)
Driver Requirements
Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file.
Video Application on Host PC
Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information.
Controlling TL6032 from the Host PC via USB UART
TL6032 supports the USB UART functionality. FCB cameras connected to TL6032 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1).
TL6032 | Production Kit
Partnumber
Content
TL6032
USB 3.0 Board
TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL6032-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100-USB
Power supply and control interface board
PS-TE10A05
5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB-SA
USB to serial adapter
TL-EVK-BRA
Bracket and screws
TL-EVK-USB3-A-MICROB
USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector
The TL6035 USB 3.0 interface board from AIVION is a tiny and easy to use HDTV USB3.0 video capture interface for the block cameras. The module receives digital video signals and sends UVC (USB Videl Class) compliant data packets to a connected
host computer. Our compact TL6035 module enables the design of small camera systems that need only a single connection between camera and PC. Video stream, control data and power will be connected by a USB 3.0 cable. For camera blocks that
need more than 900 mA during startup a Y-cable is required.
Features:
USB 3.0 Video Output
Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format
1920x1080p @ 25Hz, 29.97Hz, 30 Hz
1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz
The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer
Small Form Factor
Small form factor 45mm x 40mm
USB
Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported)
Host computer must run a UVC capable operating system
Parallel up- and downstream of camera control and status data is possible (USB CDC)
Power
Full USB bus powered camera solution possible depending on camera
Power supply voltage for camera is generated onboard
Allows an external power supply
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Temperature Range
Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Datasheet TL6035 V2.0.0
Application Note TL6035
TL6035 Block Diagram
Power Input:
5V DC from USB3 port
Characteristics:
Power consumption (FCB-EV75xx + TL6035) 5.6W
Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive)
Power consumption TL6035: 2.7W/540mA@5V DC (max.)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80%
TL6035 PCB Connectors
J6 USB3 microB connector
Vertical
J2 LVDS Video In
30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit.
J7 External Power Supply
Pin
Signal
1
Input voltage 5V to 7V DC
2
Input voltage 5V to 7V DC
3
System reset, pull to GND for reset
4
GND (0V)
5
GND (0V)
J9 RS232 UART Connector
Pin
Signal
1 to 7
do not connect
8
GND
9
RXD (host to camera)
10
TXD (camera to host)
TL6035 PCB Outline
Camera Power
Camera supply voltage is generated on TL6035 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera.
NOTE:
USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and
SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6035.
TL6035 EXTERNAL POWER OPTION:
TL6035 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external
power supply is used, this voltage is used on TL6035 for the camera supply boost converter only. All other electronic devices on TL6035 are always powered from USB3 port. No adjustments on TL6035 are required for using external power.
When powering up such a configuration, external power must be supplied before or coincident with USB3 power.
Host (PC) - Device Communication
TL6035 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6035 via a serial communication channel (USB UART).
Connecting the TL6035 to the Host PC
Operating System Support
TL6035 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems:
Windows 7 (32 and 64bit)
Windows 8.1 (32 and 64bit)
Windows 10 (64bit, version 1511)
Driver Requirements
Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8
. Manual driver installation is not necessary. For the USB UART feature, the
class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file.
Video Application on Host PC
Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own
applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information.
Controlling TL6035 from the Host PC via USB UART
TL6035 supports the USB UART functionality. FCB cameras connected to TL6035 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol.
Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1).
TL6035 | Production Kit
Partnumber
Content
TL6035
USB 3.0 Vertical Micro B USB Board
TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n
TL6035-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100-USB
Power supply and control interface board
PS-TE10A05
5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB-SA
USB to serial adapter
TL-EVK-BRA
Bracket and screws
TL-EVK-USB3-A-MICROB
USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector