Camera & Video Interfaces for Inspection

The TL9801 CVBS analog video interface from AIVION is a small form factor module to convert LVDS. Features: CVBS analog video output CVBS pass through from camera. Camera must be set to CVBS PAL or NTSC operating mode. Small form factor Small form factor 44mm x 38mm Camera Control USB2 UART based camera control Power 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Temperature Range Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Download TL9801 Datasheet V1.0.0 TL9801 Block Diagram Power Input: 9V TO 12V regulated Power consumption (MP1110M-VC + TL9801) 3.2 W (cam motors inactive) Operating and Storage Conditions: Operating: Ambient Temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% Storage: Ambient Temperature (min/max): -20°C/+60°C = -4°F/140°FHumidity: 20%-80% TL9801 PCB Connectors J1 DC Jack Fitting plug inner/outer diameter: 2.55mm/5,5mm Center Pin DC Power Input - Shield GND J2 USB2 micro connector USB2 UART camera control interface USB2 UART chip Cypress CY7C65213 J5 MCX Coaxial connector Primary CVBS Output J9 Micro coaxial connector J6 CVBS Output (Board to wire connector) JST BM08B-SSRS-TB Pin Signal 1 CVBS Output (alternative to J5, do not connect both) 2 GND 3 Do not connect 4 Do not connect 5 Do not connect 6 GND (0V) 7 Do not connect 8 Do not connect TL9801 PCB Outline TL9801 | Production Kit Partnumber Content TL9801 CVBS Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm (Type 1:n) TL9801-EXT | Evaluation Extension Partnumber Content PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector CK-MCX-BNC MCX to BNC connector cable

The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector. Features: One 3G-SDI/HD-SDI Output MCX connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One Analog YsPbPr Output 8pin board to wire connector Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV Pb, Pr 0,7Vpp into 75 ohms 1080p60 /59.94 /50 /30 /29.97 /25 Hz 720p60 /59.94 /50 Hz Camera Control RS232 level serial camera control interface Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface. Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Small form factor & Compliance Small form factor 46mm x 44mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements Industrial, medical, security, law enforcement Download TL7055 Datasheet TL7055 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 5.6W (FCB-EV7520A camera lens steady +TL7055) PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU) TL7055 PCB Connectors J8 SDI Video Output Samtec MCX7-J-P-H-ST-SM1 J7 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J2 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 Do not connect 8 Do not connect 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 YPbPr Video Output JST SM08B-SRSS-TB Pin Signal 1 HSync 2 VSync 3 GND (0V) 4 Pb signal output 5 GND (0V) 6 Ys signal output 7 GND (0V) 8 Pr signal output TL7055 PCB Outline Board Operation: TL7055 TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal. The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes). The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as 7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels. In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode. TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera. When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details). The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055. Test Pattern Generator (TPG) mode: TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default. TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards. The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control. The following VISCA commands are available for TPG control (all codes as hex values): TPG activation: 87 01 00 24 01 08 0A FF TPG deactivation: 87 01 00 24 01 08 06 FF TPG pattern type 100% color bar: 87 01 00 24 04 00 04 FF TPG pattern type multi pattern with moving block: 87 01 00 24 04 00 00 FF TPG video standard: 87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50 pq = 19 for 720p60 TL7055 | Production Kit Partnumber Content TL7055 3G-SDI & analog Board TLCK-B6 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K08-150 8wire cable harness for the analog YsPbPr video output TL7055-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter CK-MCX-BNC MCX to BNC connector cable

SL4651 is a small form factor HD-TVI/AHD analog HD video transmitter for Block Cameras. Camera LVDS video input signals are demultiplexed, processed and output over a MCX coaxial connector. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B-0200 cable kit is included and contains 30wire micro coaxial cable for connecting SL4651 to the camera as well as 10wire power supply and serial control cable harness. Features: High Definition analog HD-TVI or AHD output 1080p30 /25 Hz 720p60 /50 Hz Small form factor Small form factor 55mm x 36mm Camera Control RS232 and TTL level serial control interface RS485 camera control interface (optional) Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Applications Full HD integrated cameras with analog HD YPbPr output requirements Industrial, medical, security, law enforcement Download SL4651 Datasheet V2.2.0 SL4651 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 4.08W (MP1110M-VC camera lens steady +SL4651) PD = 4.56W (FCB-EV7520A camera lens steady +SL4651) PSL4651 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4561 is RoHS compliant (2002/05/EG and 2011/65/EU) SL4651 PCB Connectors J6 HD-TVI/AHD output connector Samtec MCX7-J-P-H-RA-TH1 J5 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) SL4651 PCB Outline Onboard Mode Switch: Switch #1 SL4651 Video Output Mode: OFF=HD-TVI, ON=AHD Switch #2 Camera Monitoring Mode Adjust: OFF=No change, ON*=Force 1080p30 *SL4651 onbaord microcontroller adjusts camera video output setting to 1080p30 if switch #2 is in ON position. Checking switch #2 is done once during SL4651 boot cycle. Changing switch #2 position during board operation has no effect. Also switch #1 must be preset before power is applied to SL4651. SL4651 | Production Kit Partnumber Content SL4651 HD-TVI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n SL4651-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector

SL4655 is a small form factor analog YPbPr FHD video transmitter. Camera LVDS video input signals are demultiplexed, processed, converted to analog and output over 6pin board to wire connector. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B5 cable kit is included and contains 30wire micro coaxial cable for connecting SL4655 to the camera as well as 10wire power supply and serial control cable harness and a 6wire cable harness for the video output. Features: High Definition analog HD-YPbPr output 1080p30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25 Hz Small form factor Small form factor 55mm x 36mm Camera Control RS232 and TTL level serial control interface RS485 camera control interface (optional) Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Applications Full HD integrated cameras with analog HD YPbPr output requirements Industrial, medical, security, law enforcement Download SL4655 Datasheet V1.2.0 SL4655 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 4.08W (MP1110M-VC camera lens steady +SL4655) PD = 4.56W (FCB-EV7520A camera lens steady +SL4655) P SL4655 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4565 is RoHS compliant (2002/05/EG and 2011/65/EU) SL4655 PCB Connectors J5 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J7 YPbPr Video Output JST SM6B-SRSS-TB Pin Signal 1 Y signal output 2 GND (0V) 3 Pb signal output 4 GND (0V) 5 Pr signal outpu 6 GND (0V) SL4655 PCB Outline SL4655 | Production Kit Partnumber Content SL4655 FHD LVDS to analog YPbPr Board TLCK-B5 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K06-150 6 pin flying leads cable for YPbPr, length 15cm SL4655-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector

The NanoConverter NA1011 from AIVION is part of a family of small form factor solutions for transmitting and receiving standard based video signals over different physical media such as coaxial cables and optical fibre. Different video formats and interface standards are supported from the transmitter and receiver side including DVI, HDMI, CVBS, YPbPr, RGB, 3G-SDI, HD-SDI and SD-SDI. Features One 3G-SDI/HD-SDI Input 75 Ohm MCX jacks connector. Supporting bit rates due to SMPTE292M and SMPTE424M (level A) 1.485 Gbps 1.485/1.001 Gbps 2.97 Gbps 2.97/1.001 Gbps One SDI loop out with reclocking 75Ohm MCX jacks connector. One HDMI output 19 pin HDMI connector. Compliant to HDMI 1.3 No HDCP support Output Data format RGB444, 3x10 bit Extendet Temperature Range -25°C to +70°C (-13°F to 158°F), Humidity 20% to 70% Small form factor PCB dimensions 38mm x 38mm Native video signal processing No image scaling, no format conversion. Download NA1011-ET Datasheet NA1011-ET Block Diagram Operating Range -25°C to +70°C (-13°F to 158°F), Humidity 20% to 70% Vin (DC) min typ max 5V 12V 18V Input Current Requirements At 25°C ambient temperature Vin 3G Operation HD Operation Condition 5V 510mA 450mA Shutdown = Vin or OPEN 12V 220mA 200mA Shutdown = Vin or OPEN 18V 160mA 145mA Shutdown = Vin or OPEN 5-18V < 10mA < 10mA Shutdown = GND NA1011-ET PCB Connectors J3 HDMI Output Connector Samtec HDMR-19-02-F-SM-PF Pin assignment due to HDMI standard J2 (In)/ J7 (Out) 3G-SDI and HD-SDI Connectors MCX 75Ohm The NA1011-ET has straight MCX connectors. Right angled MCX connectors are optional available. J1 Power Connector JST SM03B-SRSS-TB Pin Signal 1 Vin DC input, 5V to 18V 2 Shutdown/Reset, has pull up resistor of 4,7kOhm to Vin 3 GND (0V) J4 Serial Control Interface JST SM08B-SRSS-TB Pin Signal 1 reserved, do not connect 2 reserved, do not connect 3 reserved, do not connect 4 GND 5 RX data (host to device), 3.3V TTL, 4V max. 6 TX data (host to device), 3.3V TTL, 4V max. 7 GND 8 reserved, do not connect NA1011-ET PCB Outline Notes NA1011-ET The Nanoconverter products are RoHS, REACH and UL/UR compliant. The device detects and measures video input parameter and adjusts all necessary settings accordingly. Manual control is not required. However, the serial control interface can be used for status checking. Any terminal software can be used, whereas parameters have to be set to 38400bps, 8 data bits, no parity and 1 stop bit (8N1). No handshake must be used The current device version does not support audio. The device version does not process HDCP encrypted HDMI input signals. NA1011-ET | Production Kit Partnumber Content NA1011-ET Converter with straight MCX connectors TLCK-FL03-150 3pin flying leads cable for power, lead length = 15cm / 5.9inch 

The NanoConverter NA1012B-ET from AIVION is a very small form factor HDMI to SDI converter module. It is designed for applications where minimum size and a wide operating temperature range have the highest priority. For this purpose, HDMI input video and power supply voltage are supplied over a board2board connector eliminating the need for HDMI and power cables. The converter module can be easily plugged onto system boards, having a mating board2board connector available. SDI video output is available on two right-angled MCX coaxial connectors. Features One HDMI input HDMI input over board to board connector. Compliant to HDMI 1.4a and DVI 1.0.Input format support: RGB 444 YCbCr 444 YCbCr 422 Two SDI outputs 75 ohm MCX jacks connector. Supporting bit rates due to SMPTE292M and SMPTE424M 1.485 Gbps 1.485/1.001 Gbps 2.97 Gbps 2.97/1.001 Gbps Full-HD Support Supported Video formats: 1080p at 50/25/24/59.94/29.97/23.98/60/30 1080i at 50/59.94/60 720p at 50/ 59.94/60 Extendet Temperature Range -40°C/+85°C = -40°F/185°F Humidity: 20% - 80% Small form factor PCB dimensions 38mm x 38mm Native video signal processing No image scaling, no format conversion. Download NA1012B-ET Datasheet V1.0.2 NA1012B-ET Block Diagram NA1012B-ET PCB Connectors J2 Board to Board Connector Samtec Board2Board, ERM8-013-05.0-L-DV-TR Samtec ERF8-013-05.0-L-DV-TR mating connector is required on the system board Pin Signal 1 Reset (same operation as J1 pin2) 4,6 HDMI_CLK_N, HDMI_CLK_P 17,19 HDMI_DATA2_N, HDMI_DATA2_P 11,13 HDMI_DATA1_N, HDMI_DATA1_P 5,7 HDMI_DATA0_N, HDMI_DATA0_P 2,3,9,14 GND(0V) 15,21 GND(0V) 18 HDMI_HPD (hot plug detect) 8 HDMI_CEC 10,12 HDMI_DDC_CLK, HDMI_DDC_DATA 16 HDMI_5V_input 20 VIN DC supply input (same as J1 pin1) 23,25 RXD_TTL, TXD_TTL (same as J3 pin1/pin2) 22,24,26 Do not connect J5 / J6 3G-SDI and HD-SDI Output Connectors MCX 75 ohms, Samtec MCX7-J-P-H-RA-TH1 J1 Power Connector Wuerth WTB 1.25mm, 653 103 131822 Pin Signal 1 VIN, DC Supply voltage input 2 Reset (has 4k7 pullup to VIN) - Pull pin 2 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 3 GND (0V) J3 Serial Control Interface Wuerth WTB 1.25mm, 653 104 131822 Pin Signal 1 RXD_TTL (3,3V debug interface data input) 2 TXD_TTL (3,3V debug interface data output) 3 GND (0V) 4 Do not connect J2 Board to Board Connector Signal/Pin Assignement NA1012B-ET PCB Outline Notes NA1012B-ET NA1012B-ET converts video signals received from a DVI or HDMI source for transmission over an 3G/HD-SDI interface which requires clock signals to be in a well defined range. This might not be the case when standard HDMI or DVI output of desktop computers, laptop computers ot other consumer devices are used as signal source. The HDMI/DVI TMDS input clock requirements are: 3G mode: 148.5MHz or 148.5 MHz/1.001 +/- 60ppm HG mode: 74.25MHz or 74.25MHz/1.001 +/- 80 ppm The current device version does not support audio. NA1012B-ET does not process HDCP encrypted HDMI input signals. The device detects and measures video input parameter and adjusts all necessary settings accordingly. Manual control is not required. However, the serial control interface can be used for status checking. Terminal software like TeraTerm can be used, whereas parameters have to be set to 38400bps, 8 data bits, no parity and 1 stop bit (8N1). No handshake must be used. Depending on the system configuration and thermal as well as mechanical design of the system board, a heat sink might be required. In such a case the heat sink or heat pipe should contact to one of the devices marked with a yellow square (see images below), NA1012B-ET Heat Sink EK-PA1131 For test and evaluation purposes adaptor EK-PA-1131 is available. It provides a HDMI A-type connector for video input as well as USB2 connector which can be used to supply 5V DC power to NA1012B-ET. In addition it allows easy access to the debug/status port by an USB2 UART. Power and Environment Power Input 5V to 15V DC regulated supply input voltage range Characteristics PD = 2.1W (12V DC, video 1080p60) IDD = 0.17A (TA = 25°C, Humididty = 40%) Operting Conditions Ambient temperature (min/max) -40°C/+85°C = -40°F/185°F Humidity: 20% - 80% Storage Conditions Ambient temperature (min/max) -10°C/+60°C = 14°F/140°F Humidity: 20% - 80% NA1012B-ET | Production Kit Partnumber Content NA1012B-ET HDMI to 3G/HD-SDI Converter Board NA1012B-ET-EXT | Evaluation Extension Partnumber Content EK-PA-1131 Evaluation Adaptor for NA1012B-ET TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PS-EP-TA20EWE USB Power supply (5 V/2A or 9V/1,67A) CK-MCX-BNC MCX to BNC connector cable TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter