Camera & Video Interfaces for Traffic Control

The TL6032 interface is a HDTV USB 3.0 compliant video streaming capture solution from AIVION. As no analog to digital conversion is done on these modules, excellent output image quality is guaranteed. Features: USB 3.0 Video Output Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format 1920x1080p @ 25Hz, 29.97Hz, 30 Hz 1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer Small Form Factor Small form factor 45mm x 40mm USB Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported) Host computer must run a UVC capable operating system Parallel up- and downstream of camera control and status data is possible (USB CDC) Power Full USB bus powered camera solution possible depending on camera Power supply voltage for camera is generated onboard Allows an external power supply Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Temperature Range Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Download TL6032 V2.0.0 Datasheet TL6032 Block Diagram Power Input: 5V DC from USB3 port Characteristics: Power consumption (FCB-EV75xx + TL6035) 5.6W Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive) Power consumption TL6035: 2.7W/540mA@5V DC (max.) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80% TL6032 PCB Connectors J6 USB3 microB connector Horizontal J2 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. J7 External Power Supply Pin Signal 1 Input voltage 5V to 7V DC 2 Input voltage 5V to 7V DC 3 System reset, pull to GND for reset 4 GND (0V) 5 GND (0V) J9 RS232 UART Connector Pin Signal 1 to 7 do not connect 8 GND 9 RXD (host to camera) 10 TXD (camera to host) TL6032 PCB Outline Camera Power Camera supply voltage is generated on TL6032 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera. NOTE: USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6032. TL6032 EXTERNAL POWER OPTION: TL6032 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6032 for the camera supply boost converter only. All other electronic devices on TL6032 are always powered from USB3 port. No adjustments on TL6032 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power. Host (PC) - Device Communication TL6032 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6032 via a serial communication channel (USB UART). Connecting the TL6032 to the Host PC Operating System Support TL6032 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems: Windows 7 (32 and 64bit) Windows 8.1 (32 and 64bit) Windows 10 (64bit, version 1511) Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information. Controlling TL6032 from the Host PC via USB UART TL6032 supports the USB UART functionality. FCB cameras connected to TL6032 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1). TL6032 | Production Kit Partnumber Content TL6032 USB 3.0 Board TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL6032-EXT | Evaluation Extension Partnumber Content EK-PA1100-USB Power supply and control interface board PS-TE10A05 5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter TL-EVK-BRA Bracket and screws TL-EVK-USB3-A-MICROB USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector

The TL6035 USB 3.0 interface board from AIVION is a tiny and easy to use HDTV USB3.0 video capture interface for the block cameras. The module receives digital video signals and sends UVC (USB Videl Class) compliant data packets to a connected host computer. Our compact TL6035 module enables the design of small camera systems that need only a single connection between camera and PC. Video stream, control data and power will be connected by a USB 3.0 cable. For camera blocks that need more than 900 mA during startup a Y-cable is required. Features: USB 3.0 Video Output Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format 1920x1080p @ 25Hz, 29.97Hz, 30 Hz 1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer Small Form Factor Small form factor 45mm x 40mm USB Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported) Host computer must run a UVC capable operating system Parallel up- and downstream of camera control and status data is possible (USB CDC) Power Full USB bus powered camera solution possible depending on camera Power supply voltage for camera is generated onboard Allows an external power supply Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Temperature Range Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Datasheet TL6035 V2.0.0 Application Note TL6035 TL6035 Block Diagram Power Input: 5V DC from USB3 port Characteristics: Power consumption (FCB-EV75xx + TL6035) 5.6W Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive) Power consumption TL6035: 2.7W/540mA@5V DC (max.) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80% TL6035 PCB Connectors J6 USB3 microB connector Vertical J2 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. J7 External Power Supply Pin Signal 1 Input voltage 5V to 7V DC 2 Input voltage 5V to 7V DC 3 System reset, pull to GND for reset 4 GND (0V) 5 GND (0V) J9 RS232 UART Connector Pin Signal 1 to 7 do not connect 8 GND 9 RXD (host to camera) 10 TXD (camera to host) TL6035 PCB Outline Camera Power Camera supply voltage is generated on TL6035 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera. NOTE: USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6035. TL6035 EXTERNAL POWER OPTION: TL6035 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6035 for the camera supply boost converter only. All other electronic devices on TL6035 are always powered from USB3 port. No adjustments on TL6035 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power. Host (PC) - Device Communication TL6035 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6035 via a serial communication channel (USB UART). Connecting the TL6035 to the Host PC Operating System Support TL6035 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems: Windows 7 (32 and 64bit) Windows 8.1 (32 and 64bit) Windows 10 (64bit, version 1511) Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information. Controlling TL6035 from the Host PC via USB UART TL6035 supports the USB UART functionality. FCB cameras connected to TL6035 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1). TL6035 | Production Kit Partnumber Content TL6035 USB 3.0 Vertical Micro B USB Board TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL6035-EXT | Evaluation Extension Partnumber Content EK-PA1100-USB Power supply and control interface board PS-TE10A05 5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter TL-EVK-BRA Bracket and screws TL-EVK-USB3-A-MICROB USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector

The TL7050 Dual 3G/HD-SDI and DVI(HDMI) Output Video Transceiver module from AIVION connect to the digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M  HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One HDMI Output HDMI connector (Kycon KDMIX_FS1V_WS) 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Video input and Compliance Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7050 V 2.5.0 Datasheet TL7050 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Characteristics: Power consumption TL7050: 260mA @ 12V DC (typ.) Operating and Storage Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7050 PCB Connectors J8 HDMI connector Kycon KDMIX_FS1V_WS J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7050 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output TL7050 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7050 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7050 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7050 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7050 Analog Video Output TL7050 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7050, the camera is also automatically powered. During power up all functions on TL7050, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7050. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7050 | Production Kit Partnumber Content TL7050 HDMI-HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7050-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

The TL7051 Dual 3G/HD-SDI Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and supports several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M  HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7051 Revision D V.3.0.0 Datasheet TL7051 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7051 PCB Connectors J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7051 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7051 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND TL7051 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low ( < 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7051 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7051 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7051 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7051 Analog Video Output TL7051 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7051, the camera is also automatically powered. During power up all functions on TL7051, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7051. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7051 | Production Kit Partnumber Content TL7051 3G-SDI/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7051-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable

The TL7052 DVI(HDMI) Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera One HDMI Output HDMI connector (Kycon KDMIX_FS1V_WS) 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7052 V 2.4.0 Datasheet TL7052 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7052 PCB Connectors J8 HDMI connector Kycon KDMIX_FS1V_WS J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7052 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 Analog component YPbPr and CVBS output Requires TL7052 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND J4 24pin FFC Connector Power, Reset, Serial Control IF, analog Video TL7052 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7052 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7052 Analog Video Output TL7052 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7052, the camera is also automatically powered. During power up all functions on TL7052, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7052. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7052 | Production Kit Partnumber Content TL7052 HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7052-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector. Features: One 3G-SDI/HD-SDI Output MCX connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One Analog YsPbPr Output 8pin board to wire connector Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV Pb, Pr 0,7Vpp into 75 ohms 1080p60 /59.94 /50 /30 /29.97 /25 Hz 720p60 /59.94 /50 Hz Camera Control RS232 level serial camera control interface Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface. Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Small form factor & Compliance Small form factor 46mm x 44mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements Industrial, medical, security, law enforcement Download TL7055 Datasheet TL7055 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 5.6W (FCB-EV7520A camera lens steady +TL7055) PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU) TL7055 PCB Connectors J8 SDI Video Output Samtec MCX7-J-P-H-ST-SM1 J7 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J2 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 Do not connect 8 Do not connect 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 YPbPr Video Output JST SM08B-SRSS-TB Pin Signal 1 HSync 2 VSync 3 GND (0V) 4 Pb signal output 5 GND (0V) 6 Ys signal output 7 GND (0V) 8 Pr signal output TL7055 PCB Outline Board Operation: TL7055 TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal. The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes). The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as 7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels. In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode. TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera. When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details). The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055. Test Pattern Generator (TPG) mode: TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default. TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards. The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control. The following VISCA commands are available for TPG control (all codes as hex values): TPG activation: 87 01 00 24 01 08 0A FF TPG deactivation: 87 01 00 24 01 08 06 FF TPG pattern type 100% color bar: 87 01 00 24 04 00 04 FF TPG pattern type multi pattern with moving block: 87 01 00 24 04 00 00 FF TPG video standard: 87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50 pq = 19 for 720p60 TL7055 | Production Kit Partnumber Content TL7055 3G-SDI & analog Board TLCK-B6 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K08-150 8wire cable harness for the analog YsPbPr video output TL7055-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter CK-MCX-BNC MCX to BNC connector cable