Block Camera integration

HDMI, SDI, USB3, Analog, IP based?

Why Block Cameras?

Block cameras have become very popular since they combine some very important features with an open and flexible system architecture. The big strength of block cameras is that they usually come with an optical zoom lens, autofocus capabilities, and a compact housing.

Since different markets require different video standards, most state-of-the-art block cameras provide a 30pin LVDS, HDMI, or MIPI interface. To enable system integrators to select the video transmission standard for their application, AIVION does provide interface solutions for a lot of different block camera models.

The remaining key question for a lot of system integrators is:


Block Cameras Integration

What is the best video transmission standard for my application?

There are many options for how a camera subsystem could be integrated into a product. The reason for the wide range of interfaces is the fact that there is no single standard that has only strengths. There is always a “but”. In an ideal world, system integrators would like to combine the following:

Low latency

High-Quality Video

Without artifacts and noise

High-Resolution

High-Res Video Streams

Low cost of cabling

Many frames per seconds

Low power consumption

Transmission over long Distance

High flexibility

to connect to different types of equipment

Since there is no simple answer to which video transmission is the best, most block camera vendors decided to offer cameras with an LVDS (Low Voltage Differential Signal) interface that, leaves the question of the right video transmission open to the system integrator. Those camera blocks can be combined with many different standard interfaces to create the perfect fit for your system requirements.

Which video transmission do I need?

To decide which video transmission is the best fit for a certain application, it is important to understand the system's needs. To understand the pros and cons of the various standards, let’s look at the different specification criteria.
video-compression

Latency

The importance of latency is why many block camera integrators use non-IP video transmission. Video signals from most block cameras do provide uncompressed high-quality video signals. Those video signals require a lot of bandwidth. A Full-HD video signal with a resolution of 1920 pixels and 1080 lines transmitted 60 times per second (called 1080p60) requires 3 Gbit of data per second. IP-based video systems use data compression techniques to minimize the needed bandwidth. There are different compression methods like M-JPEG, MPEG4, or H.264. Some standards use compression techniques looking for redundancies within a frame, while others can also use multiple frames to minimize the data. As more frames, a system uses to decode and encode the video stream, as higher the latency usually is. IP-based video interfaces have a higher system latency than non-compression-based USB3, HDMI, SDI, or analog Interfaces.

Image Quality

The image quality depends on the camera block. The important factors are sensor size, sensor sensitivity, lens quality, and image processing in the camera. If the video transmission requires video compression, the interface can have a negative impact on the video quality since compression techniques that are not using visual lossless compression techniques will add artifacts and cost some details in the image. Our USB3, HDMI, or SDI interfaces do not have a negative impact on the video quality since we do not use any compression methods here.

Camera objectiv
Monitor resolutions

Resolution

The current generations of block cameras are digital cameras with CMOS sensors. Typical resolutions are:

  • HD (1280 x 720)
  • Full-HD (1920x1080)
  • WQHD (2560x1440)
  • UHD (3840x1260)

The higher the resolution, the more bandwidth it takes to transmit the uncompressed video stream. Sometimes selecting a specific video standard may exclude a particular resolution. WQHD, for example, can be used for an HDMI interface, but the SDI standard does not specify this resolution. Therefore, our SDI interfaces (coax and fiber) do not support the WQHD resolution. Some cameras group pixels together if a lower resolution is chosen. The advantage of those “larger” pixels is that they can catch more light and improve low-light performance. The downside is the lower resolution. If you use a camera in this mode, it is important that the interface can deal with both modes.

Low cost of cabling

Cabling costs could be high in a video installation, but it is crucial to understand the limitation of each system. USB-based systems have the advantage that you can capture a video directly with a PC, but if the camera is 10, 30, or more meters away, it is not the best option. Standards like USB or HDMI did not target applications that require long distances. If a video system needs to support longer distances, other standards may help. HD transmission through analog technology (HD-TVI or AHD) could be a solution if SDI over Coax or fiber is too expensive. For long distances, the highest quality and low latency optical transmission might be the only option in some cases.
cabling cost
Frames per Second Overview

How many frames per second?

The higher the image's resolution and the higher the frame rate of the video, the more bandwidth is required. In SD-SDI Systems (the old PAL or NTSC standards that usually used data rates around 270 Mbit/s), transmission length could be around 300m. The HD-Standards (1.5Gbit/s or 3Gbit/s) typically have not more than 100m. But also here, it makes a difference if the video format is interlaced (only half frames are transmitted) or progressive and if the frame rate is 25, 30, 50, or 60 frames per second. So, the data rate of a 720p25 signal is much lower than that of a 1080p60 video, and the transmission length is longer for the 720p25 than for the 1080p60 video if the same SDI cable is used. But other factors might require specific video settings. Depending on your net's illumination and frequency (220V50Hz or 110V60Hz, for example), your video may flicker if your display has the wrong frame rate. In addition, not every monitor or recorder supports all frame rates. For that reason, most block cameras support multiple frame resolutions and frame rates. But those are a fixed number of supported values. Block cameras usually do not support variable frame rates like five frames per second or 11 frames per second, or whatever an industrial application might need. If such a solution is required, the image needs to get stored in a frame buffer, and a specific frame rate converter is required. This might be a topic for a customized product.

Video Transmission over a long distance

There is no alternative to optical solutions for applications that need video transmission over long distances (a couple of hundred meters or even kilometers), at least if the video is uncompressed. Since compression usually adds a lot of latency and artifacts, many systems require uncompressed video transmission. Depending on the system architecture, it is possible to control the camera system (parameters like zoom, focus, and illumination) through the same coax or fiber cable that transmits the video. To realize these specific interfaces are needed and available from the AIVION brand. For HD-SDI applications that only require medium distances (for example, 30-50m indoors), it is possible to use the Coax cable to provide power! So power, control, and video would go through one single coax cable in that case.

optical fibre cable for block cameras

High flexibility to connect to different types of equipment

The combination of block cameras and specific interfaces allow systems integrators to realize an optimized system architecture without developing their own boards and reinventing the wheel. A wide range of different block camera models (from 10x optical zoom to more than 30x optical zoom, from small form factors to larger models with larger sensors, from low prices segments to high-end models) in combination with analog, HDMI, USB3, and 1.5G, 3G or 6G SDI standards do allow to create a nearly perfect fit for a lot of different video system requirements.

HD Block Cameras

AIVION AZM-FS10L
Full-HD 10X optical zoom moduleFeaturesEffective numbers of Pixels: Approx. 2,100,000 pixelsImage sensor: 1/2.8 inch Sony Starvis CMOS Sensor (Progressive Scan)Lens: Optical 10x, f = 4.7 mm to 47.0 mm (F 1.6 to F 3.0)Horizontal viewing angle (wide to tele): 57.7 degrees(WIDE), 6.4 degrees(TELE)Digital Zoom: 12xVideo Output Digital: LVDS Digital ITU-R BT.1120 - YcbCr4:2:2 16bitsVideo Output Analog: SD CVBS (NTSC/PAL), 1.0Vp-p 75, CompositeCamera Control Interface: Visca Protocol

Price on request

AIVION AZM-WQHS36L-LL
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL3K7052 | WQHD | HDMI Video Interface
WQHD 36X Optical Zoom ModuleFeaturesEffectiv numbers of Pixels: Approx. 5,450,000 pixelsImage sensor: 1/1.8" Sony IMX178LQJ-C CMOS Sensor (Progressive Scan)Lens: Optical 36x, f = 6.0 mm to 216 mm (F 1.5 to F 4.8)Horizontal viewing angle (wide to tele): 49.27 degrees(WIDE) to 1.85 degrees(TELE)Digital Zoom: 32xVideo Output Digital: LVDSVideo Output Analog: HD-Analog / CVBS(※ Test Only)Camera Control Interface: Visca Protocol

Price on request

Sony FCB-EV7100
Capture crisp, clear Full HD (1080/60p) images*2The high-performance 1/2.8-type Exmor™ CMOS image sensor achieves superb Full HD (1920 x 1080) picture quality, even in lowlight environments. Progressive scanning assures smoother pictures with reduced blur – ideal for capturing the detail in moving images. 10x Optical zoom lensFCB-EV7100 is equipped with a bright F1.8 maximum aperture 10x optical zoom lens. StableZoom™Image stabilizer and optical/digital zoom are combined to enhance picture quality while maintaining the original horizontal angle of view, ensuring no compromise in image size and reduced blurring. 2D/3D Noise ReductionAdvanced noise reduction technology filters noise from the image for clearer results, especially in low light conditions. Noise reduction can be selected from five levels to suit a wide range of operating environments.See more clearly with Visibility Enhancer and De-fogPicture quality is enhanced dynamically and adaptively on a pixel-by-pixel basis while continuously adapting to the scene within the given dynamic range. There’s also a de-fog feature that allows clearer viewing in foggy or misty scenes. Wide dynamic rangeWide-D image processing technology gives the ability to see clear detailed images in high-contrast or backlit environments. Clear vision round the clock with Day/NightBenefit from optimized picture quality in changing light conditions – a frequent challenge in round-the-clock security operations. In high sensitivity mode the camera can operate eff ectively in lightinglevels as low as 0.35 lx (ICR on).*5  Auto ICR (Auto IR-cut Filter Removal)In low light conditions the camera automatically switches from day to night mode, removing the IR-cut fi lter to boost sensitivity for clear pictures in near-darkness. Spherical privacy zone maskingAreas of view can be selectively masked for privacy. Masked areas are automatically interlocked with the camera’s pan/tilt/zoom movements. Choice of HD and SD output modesVideo signal outputs are available in a range of HD (digital and analog) and SD formats, reducing integration cost and complexity by avoiding the need for additional analog/digital converters. Videooutput modes can be changed ‘on the fly’ during normal operation, without a hardware reboot of the camera. One-cable connection for simpler integrationA single cable carries HD video signals plus VISCA communication and power supply. Integration flexibility is further supported by both 30-pin micro coaxial (digital output) and 24-pin FFC (analog output) interfaces. Wide range of features for versatile operationVersatile operation is ensured by a wide range of functions and adjustments, including: White Balance modes; Picture effects (E-Flip, Nega Art, Black & White, Mirror Image, Colour Enhancement);Motion Detection/Alarm; Picture freeze; Temperature readout; Slow AE response; Electronic shutter/slow shutter; Title display/ Camera mode display (English).

Price on request

Sony FCB-EV7520
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: SL4651 | Analog | HD-TVI Video Interface
The FCB-EV7520 camera block incorporates a 1/2.8-type Exmor RTM CMOS sensor, providing Full-HD video with extraordinary sensitivity. In addition, the Sony block camera includes STARVISTM technology to realize high picture quality in visible light and near-infrared light. With 30x optical zoom and either HD or Full-HD capability, the camera inherits a multitude of Sony’s FCB features, including Auto ICR, Spherical Privacy Zone Masking, and Defog. Sony FCB-EV7520 Features  30x Enhanced Optical Zoom Digital Zoom 12x (360x with optical zoom) Full HD (1080p/60) Image Sensor 1/2.8-type Exmor R CMOS Minimum illumination Colour: 0.01 lx (F1.6,AGC on, 1/30 s) Defog · High Light Compensation · Wide Dynamic Range Super Image Stabilizer Auto IR-cut Filter Removal Spehrical privacy zone masking Noise reduction Slow AE response Datasheet Sony FCB-7520 Series Overview Features FCB-EV7520 Capture crisp, clear Full-HD (1080/60p) Even in low-light environments, the high-performance 1/2.8-type Exmor CMOS image sensor achieves outstanding Full-HD (1920 x 1080) picture quality. Progressive scanning assures smoother pictures with reduced blur – ideal for capturing the detail in moving images. Get a steadier picture with the image stabilizer. The camera's built-in image stabilizer function counters the effect of blurred, shaky images caused by low-frequency vibration. It is helpful for outdoor surveillance and traffic monitoring applications, mainly if the camera is used on a bridge or mounting pole where it is subjected to wind or mechanical vibration. Stable Zoom Image stabilizer and optical/digital zoom are combined to improve image quality while maintaining the original horizontal viewing angle. This does not affect the image size and reduces blu. 2D/3D noise reduction Advanced noise reduction technology filters noise from the image for clearer results, especially in low-light conditions. Noise reduction can be selected from five levels to suit a wide range of operating environments. Wide dynamic range Wide-D image processing technology allows one to see clear, detailed images in high-contrast or backlit environments. Models now support an extensive 130 dB dynamic range activated via the VISCA command. De-fog The de-fog feature allows more precise and natural viewing in foggy or misty scenes. The camera detects the haze level and automatically applies the required effects when this feature is activated. Depending on user requirements, the level of these effects can be adjusted via the VISCA command. HLC (High Light Compensation) HLC technology helps to improve, for example, the visibility of license plates when bright headlights are shot under low-light conditions. The bright parts in the image are masked and compensated automatically to achieve better visibility. Auto ICR (Auto IR-cut Filter Removal) In low-light conditions, the camera automatically switches from Day to Night mode, removing the IR-cut filter to boost sensitivity for clear pictures in near-darkness. The spherical privacy zone masking feature enables areas of view to be selectively masked for privacy. Masked areas are automatically interlocked with the camera’s pan/tilt/zoom movements. Privacy Zone Masking Privacy Zone Masking protects private objects and areas such as house windows, entrances, and exits within the camera’s range of vision but is not subject to surveillance. Privacy zones can be masked on the monitor to protect privacy. Wide range of features for versatile operation Versatile operation is ensured by a wide range of functions and adjustments, including White Balance modes; Picture effects (E-Flip, Nega Art, Black & White, Mirror Image, Colour Enhancement); Motion Detection/Alarm; Picture freeze; Temperature readout; Slow AE response; Electronic shutter/ slow shutter; and Title display/Camera mode display (English). Sony FCB-EV7520 Specifications Feature Sony FCB-EV7520 Image sensor 1/2.8-type Exmor R CMOS Image sensor (Number of effective pixels) Approx.2.13 Megapixels Signal system 1080p/59.94,1080p/50, 1080p/60, 1080p/30, 1080p/29.97, 1080p/25, 1080i/59.94, 1080i/50, 1080i/60, 1080i/30, 720p/59.94, 720p/50, 720p/60, 720p/30, 720p/29.97, 720p/25, NTSC, PAL Minimum illumination (50%) High sensitivity mode Colour: 0.01 lx (F1.6, AGC on, 1/30s) Minimum illumination (50%) Normal mode Colour: 0.1 lx (F1.6, AGC on, 1/30s) S/N ratio More than 50 dB Gain Auto/Manual Auto/Manual 0 dB to 50.0dB (0 to 28 steps +2 step/ total 15 steps) Gain Max. Gain Limit Max. Gain Limit 10.7 dB to 50.0 dB (6 to 28 steps +2 tep/ total 12 steps) Shutter speed 1/1 s to 1/10,000 s, 22 steps Sync system Internal Exposure control Auto, Manual, Priority mode (shutter priority & iris priority), Bright, EV compensation, Slow AE Backlight compensation Yes Aperture control 16 steps White balance Auto, ATW, Indoor, Outdoor, Outdoor Auto, Sodium Vapor Lamp (Fix/Auto/Outdoor Auto), One-push, Manual Lens 30x optical zoom f = 4.3 mm (wide) to 129.0 mm (tele) F1.6 to F4.7 Digital zoom 12x (360x with optical zoom) Focusing system Auto (Sensitivity: normal, low), One-push AF, Manual, Interval AF, Zoom Trigger AF, Focus compensation in ICR on Horizontal viewing angle 1080p mode 63.7° (wide end) to 2.3° (tele end) Horizontal viewing angle 720p mode 63.7° (wide end) to 2.3° (tele end) Horizontal viewing angle SD 47.8° (wide end) to 1.7° (tele end) Minimum object distance 10 mm (wide end) to 1200 mm (tele end) (Default: 300 mm) Auto ICR Yes Wide-D Yes (120 dB) Visibility Enhancer Yes De-fog Yes HLC Yes Noise reduction Yes (6 steps) Image stabilization Yes StableZoom Yes Spherical privacy zone masking Yes Motion detection Yes Alarm Yes Slow AE response Yes Picture effects E-Flip, Nega Art, Black & White, Mirror image, Colour enhancement Picture freeze Yes Slow shutter Yes Temperature readout Yes Title display Yes Camera mode display 20 characters/line, max. 11 lines Key switch control Yes Camera operation switch Yes Video output HD Analog N/A Video output HD Digital Digital:Y/Cb/Cr 4:2:2 via LVDS (Signal format conforms to SMPTE 274/SMPTE 296.) Video output SD VBS Camera control interface VISCA (CMOS 5 V level) Baud rate: 9.6 Kbps, 19.2 Kbps, 38.4 Kbps, 115.2 Kbps, Stop bit: 1 bit Power requirements 6.0 V to 12.0 V DC Power consumption - Focus inactive 3.2 W (zoom/focus inactive) Power consumption - Focus active 4.0 W (zoom/focus active) Operating temperature -5°C to +60°C (23°F to 140°F) Storage temperature -20°C to +60°C (-4°F to 140 °F) Operating humidity 20% to 80%, Absolute humidity: 36 g/m3 Storage humidity 20% to 95%, Absolute humidity: 36 g/m3 Dimensions (W x H x D) 50.0 x 60.0 x 89.7 mm (2 x 2 3/8 x 3 5/8 inches) Mass 255 g (9.0 oz) Sony FCB-7520 Dimensions Sony FCB-EV7520 Front Sony FCB-EV7520 Rear Sony FCB-EV7520 Top Sony FCB-EV7520 Bottom Sony FCB-EV7520 Left Sony FCB-EV7520 Right

Price on request

Sony FCB-EV7520A
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL7050 | HD | Dual 3G-SDI & HD-SDI and HDMI Interface
Back-illuminated CMOS sensor1/2.8-type Exmor RTM CMOS image sensor provides full high-definition and high-quality images. Fine, high- quality images can be captured even at night or in dark places.High-performance 30x lensThe camera is equipped with a bright lens with 30× optical zoom and F1.6 aperture.Highly advanced ISPUsing the image signal processor (ISP), the following images can be obtained.Full HD 60 fps output imageLow focal plane distortion image using the highspeed readout of imagerSpot Light Avoidance

Price on request

Sony FCB-EV9500L
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: SL4651 | Analog | HD-TVI Video Interface
Compact size block camera with 30x enhanced optical zoom and a 1/1.8 sensor. This Full HD model with LVDS output is optimal for environments with harsh conditions. The new super image stabilizer has greatly improved blur suppression compared to conventional models. Sony FCB-EV9500L Features  Full HD (1080p/60) LVDS 30x Enhanced Optical Zoom High Sensitivity Super Image Stabilizer Flare reduction with the new iris Color image acquisition during ICR ON Spot Focus · Spot AE · Spot AWB Wide Dynamic Range (Wide-D) Visibility Enhancer (VE) Datasheet Sony FCB-9500 Series Overview Features FCB-EV9500L High Resolution Utilizing a 4M sensor and sharp lens achieve superior resolution and accurate image representation with the evolved AF/AE/ AWB functions even in low light environments. Combined with enhanced optical zoom achieve a high image quality from the Wide end to the Tele end.  High Sensitivity Through introduction of new cell structures and circuit technology, the series efficiently uses light, achieving twice the sensitivity compared to conventional image sensors. Consequently, clear images can be captured even during the night and in dark environments. Super Image Stabilizer Enables capturing of highly precise video with reduced blurring even in harsh environments with strong vibrations by greatly improving blur suppression and image stabilizer. The camera is during full HD or HD output equipped with the Super and Super modes. Applying a wide correction area using 4M pixels the camera series suppresses blurs from strong vibrations and rotational vibrations compared to conventional models. Super Suppresses strong vibrations with a wider correction area compared to conventional electronic vibration suppressors. Super + By employing a wider correction area than “Super,” “Super+” suppresses intense vibrations that cannot be suppressed with “Super.” Potential application: Shipboard, attachments for ITS surveillance, on bridges, drones, vehicles, etc. Starvis 1/1.8-type CMOS sensor The Sony FCB-EV9500L Sony blockcamera is equipped with an approximately 417 million- effective-pixel, 1/1.8-type high sensitive, AR-coated (anti-reflective coating) CMOS sensor. With a high spectral sensitivity value in near infrared to infrared, it is especially effective for security uses. Furthermore, the AR coating minimizes the ghost phenomenon and enables capturing of images without missing crucial information even during the night and in dark environments. 30x Enhanced Optical Zoom Using a compact lens designed for resolutions up to 8M the camera maximizes the coverage of the 4M sensor. The newly designed lens provides high resolution and low aberration, making it capable of capturing high resolution images that span from the Tele end from the screen center to the surrounding edges. There is no image deterioration using the 30x enhanced optical zoom. Experience full sharpness and dramatically reduced chromatic aberration in full HD output and also achieve images with sharp resolution during 4M output. Flare reduction with the new iris Diamond flares and ghosts that occur on lenses disrupts focusing and deteriorates the image quality. The new lens adopts 7 blades compared to the conventional 2 blades, improving this phenomenon by generating fine circular flares, and thus greatly improving image quality. Color image acquisition during ICR ON On conventional models, only black and white images are achieved while the IR cut filter was removed. The new ICR ON COLOR function enables the camera to capture shots with color even when the IR cut filter is removed. It is effective for color visibility in dark environments. The precision of color reproduction varies depending on the light source and brightness. Spot Focus · Spot AE · Spot AWB Enables functioning of AF, AE, and AWB only in specified areas within the screen. Enables independent specification of any rectangle of the entire screen divided in 6 x 8. For example, if the subject location is specified with Spot AE, enables capturing of images with Exposure effects reduced even if brightness changes occur outside the specified frame. Adjustable ROIs Screen divided in 6 x 8 Wide Dynamic Range (Wide-D) Wide-D mode is a function for dividing an image into several blocks for correcting blocked-up shadows and blown-out highlights in accordance with the intensity difference. It enables image acquisition in which portions ranging from dark to light can be recognized, even when capturing a subject with a large intensity difference that is backlit or includes extremely light regions of interest. Wide Dynamic Range Off Wide Dynamic Range On Sony FCB-EV9500L Specifications Specification FCB-EV9500L (Full HD· LVDS) Basic Features Image Sensor (Number of effective pixels) 1/1.8-type STARVISTM CMOS Sensor (Approx. 4.17M pixels)    Output Image Size (H x V) 1920x1080, 1280x720   Signal System 1080p/60, 1080p/59.94, 1080p/50, 1080p/30, 1080p/29.97, 1080p/25, 1080i/60, 1080i/59.94, 1080i/50, 720p/60, 720p/59.94, 720p/50, 720p/30, 720p/29.97, 720p/25   Minimum Illumination (50%, High Sensitivity Mode ON) ICR-Off mode: 0.009 lx (Shutter Speed: 1/30 s), 0.0012 lx (Shutter Speed: 1/4 s or 1/3 s) ICR-On mode: 0.00008 lx (Shutter Speed: 1/30 s), 0.000005 lx (Shutter Speed: 1/4 s or 1/3 s, 30%)   Minimum Illumination (50%, High Sensitivity Mode OFF) ICR-Off mode: 0.09 lx (Shutter Speed: 1/30 s), 0.012 lx (Shutter Speed: 1/4 s or 1/3 s) ICR-On mode: 0.00063 lx (Shutter Speed: 1/30 s)   Recommended Illumination 100 lx to 100,000 lx   Image S/N  Wide end to Tele end - 4.8 s (Focus Tracking ON), 2.9 s (Focus Tracking OFF) Wide end to Digital 12x tele - 6.1 s (29.97p/59.94p), 6.4 s(25p/50p)      Gain Auto/Manual (0 dB to 50.0 dB), 0 to 28 steps   Shutter Speed 1/1 to 1/10000 s, 22 steps   Sync System Internal   Exposure Control 0 dB to ± 10.5 dB, 15 steps   Backlight Compensation Yes   Gamma Standard / Straight gamma   Aperture Control 16 steps   White Balance Auto, ATW, Indoor, Outdoor, One Push WB, Manual WB, Outdoor Auto, Sodium Vapor Lamp (Fix/Auto/Outdoor Auto), Spot AWB   AE (Auto Exposure Mode) Full Auto, Manual, Priority mode (shutter/iris), EV compensation, Spot AE, Slow AE   Zoom 30x Enhanced Optical Zoom 36x StableZoom and 12x Digital Zoom  - StableZoom increases the magnification by combining optical zoom and digital zoom  - FCB-EW9500H: For 1080p, 1080i, and 720p only.   Lens (wide to tele) f = 6.5 mm to 162.5 mm, F1.6 to 4.8   Zoom Mode Standard Mode / Variable Mode / Direct Mode   Zoom Movement Speed Wide end to Tele end - 4.8 s (Focus Tracking ON), 2.9 s (Focus Tracking OFF) Wide end to Digital 12x tele - 6.1 s (29.97p/59.94p), 6.4 s(25p/50p) Digital wide to Digital 12x tele - 1.4 s (29.97p/59.94p), 1.6 s (25p/50p)   Focusing System Auto Focus (Normal AF, Interval AF, Zoom Trigger AF [Sensitivity: normal, low]), Manual (Standard, Variable, Direct), One Push Trigger, Full Scan One Push Trigger, Near Limit, ICR-on Correction, Spot Focus   Focus Movement Time ∞ to Near: 1.4 s   Horizontal Viewing Angle 58.1° to 2.3°   Minimum Object Distance (wide end to tele end) 100 mm to 1200mm Camera Features Auto ICR Yes   Wide Dynamic Range (Wide-D) Yes   Visibility Enhancer Yes   Defog Yes (low/mid/high)   Noise Reduction Yes (3D + 2D / Independent setting (3D, 2D))   Progressive Scan Mode Yes   Image Stabilization Yes: Super image stabilizer (Super / Super+ FCB-EW9500H: For 1080p, 1080i, and 720p only.)   Spot Light Avoidance Yes   Motion Detection Yes   Privacy Zone Masking Yes   Alarm Yes   Slow AE Response Yes   Picture Effects Black White (Monochrome Image)   Picture Freeze Yes   Electronic-Flip (E-FLIP) Yes   Mirror Image Yes   Slow Shutter Yes   Temperature Readout Yes   Title Display Yes (20 characters / line, max. 11lines)   Camera Mode Display Yes (English) Interface Video Output Digital : Y/Pb/Pr 4:2:2 (LVDS) (Y: 8 bit, C: 8 bit, Vsync, Hsync, Field, Clock) (SMPTE274M/SMPTE296M)   Camera Control Interface VISCA protocol (CMOS 3.3V Level, 5.5V tolerance); Baud Rate : 9.6 kbps, 19.2 kbps, 38.4 kbps, 115.2 kbps, Stop bit: 1 bit General Power Requirements 7.0 V to 12.0 V DC   Power Consumption 6.1 W (When motor operates: 7.8W)   Operating Temperature "-5 °C to +60 °C (23 °F to +140 °F)"   Storage Temperature "-20 °C to +60 °C (–4 °F to +140 °F)"   Operating Humidity 20% to 80% (Absolute humidity: 36 g/m3)   Storage Humidity 20% to 95% (Absolute humidity: 36 g/m3)   Dimensions (W x H x D) 56.0 x 64.0 x 125 mm (2 1/4 × 2 5/8 × 5 in.)   Mass Approx. 439 g (15 oz.)

Price on request

Tamron MP1010M-VC
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL7050 | HD | Dual 3G-SDI & HD-SDI and HDMI Interface
Features Tamron MP1010M-VC Block Camera1/3-type CMOS (Progressive Scan)10x optical zoom f=3.3 to 33.0 mm F1.8 to 3.41/2.8 type Exmor CMOSWide-Dynamic RangeVC (Vibration Compensation)Noise reduction (3D + 2D)Slow shutterPrivacy zone maskingVISCA protocolVideo Output: Digital: Y/Pb/Pr 4:2:2 (LVDS)

Price on request

Tamron MP3010M-EV
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL8651 | HD | 3G-SDI & HD-SDI Interface
Full upgrading compatibility with the previous models of MP1010/MP1110 seriesEquipped with industry-leading compact 10x zoom lens New functions for the various applications (High sensitivity, Day/Night function, Multi-interface, etc.

Price on request

4K Block Cameras

Sony FCB-ER8300
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL4K1152 | 4K | HDMI Video Interface
Key Features icons resolution, optical zoom, digital zoom, compact size, image stabilization, HDMI video output, power consumption, sensitivity, HFOV, VISCA commandsSensor 1/2,3- type Exmor R CMOSResolution 8.93 MPVideo format 4K, 1080p, 720p, 480pOptical zoom (lens) 12 xDigital zoom 12 xSuper resolution zoom 20 xWidth 60Height 60Depth 105Video output HDMI 1.4bFOV 65 °Image stabilization YesNoise reduction YesVisca command  Yes

Price on request

Sony FCB-ER8530
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL4K1152 | 4K | HDMI Video Interface
Key Features icons: resolution, optical zoom, digital zoom, image stabilization, HDMI video output, VISCA commandsSensor 1/2,5- type Exmor R CMOSResolution 8.51 MPVideo format 4K, 1080p, 720p, 480pOptical zoom (lens) 20 xDigital zoom 12 xSuper resolution zoom 30 xWidth 50Height 60Depth 93Video output HDMI 1.4bFOV 70.2 °Noise reduction Yes

Price on request

Sony FCB-ER8550
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL4K1152 | 4K | HDMI Video Interface
Key Features resolution, optical zoom, digital zoom, compact size, image stabilization, external synchronization, HDMI video output, sensitivity, HFOV, VISCA commandsSensor 1/2,5- type Exmor R CMOSResolution 8.51 MPVideo format 4K, 1080p, 720p, 480pOptical zoom (lens) 20 xDigital zoom 12 xSuper resolution zoom 30 xWidth 50Height 60Depth 93Video output HDMI 1.4bFOV 70.7 °Noise reduction Yes

Price on request

Sony FCB-ES8230
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL4K1152 | 4K | HDMI Video Interface
Key Features: optical zoom, digital zoom, image stabilization, HDMI video output, power consumption, sensitivity, HFOV, VISCA commandsSensor 1- type Exmor R CMOSResolution 20 MPVideo format 4K, 1080p, 720p, 480pOptical zoom (lens) 12 xDigital zoom 12 xSuper resolution zoom 18 xWidth 65.1Height 70.0Depth 134.8Video output HDMI 1.4bFOV 65 °Noise reduction Yes

Price on request

Sony FCB-EW9500H
AIVION Extension Kit: No Evaluation Extension Kit | AIVION Interface: TL4K1152 | 4K | HDMI Video Interface
Compact size block camera with 30x enhanced optical zoom and a 1/1.8 sensor. This 4MP model with HDMI output is optimal for environments with harsh conditions. The new super image stabilizer has greatly improved blur suppression compared to conventional models. Sony FCB-EW9500H Features  4M (2160p/60) HDMI 30x Enhanced Optical Zoom High Sensitivity Super Image Stabilizer Flare reduction with the new iris Color image acquisition during ICR ON Spot Focus · Spot AE · Spot AWB Wide Dynamic Range (Wide-D) Visibility Enhancer (VE) Datasheet Sony FCB-9500 Series HDMI Interface FCB-EW9500 series The TL4K1152 is a small form factor HDMI interface. The camera control can be managed through an RS232 port. Supported Video format: 4K mode 2160p 30/25 Full HD Mode 1080p 60/59.94/50/30/29.97/25 TL4K1152 Dual Link 3 Gbps UHD-SDI Interface FCB-EW9500 series The TL4K1161 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed, and output over straight DIN7A(10.23) connectors. Dual Link 3G-SDI output compliant to SMPTE ST425-3, 2si mapping, FHD output compliant o SMPTE ST425-1 level A Camera control is accomplished by a transparent full-duplex communication channel. Supported Video format: 4K mode 2160p 30/25 Full HD Mode 1080p 60/59.94/50/30/29.97/25 TL4K1161 Dual Link 3 Gbps UHD-SDI Interface with PCOC Feature FCB-EW9500 series The TL4K1161 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed, and output over straight DIN7A(10.23) connectors. Dual Link 3G-SDI output compliant to SMPTE ST425-3, 2si mapping, FHD output compliant o SMPTE ST425-1 level A Camera control is accomplished by a transparent full-duplex communication channel. 4K mode 2160p 30/25 Full HD Mode 1080p 60/59.94/50/30/29.97/25 TL4K1261 6 Gbps UHD-SDI Interface FCB-EW9500 series TL4K1171 is a small form factor serial digital video (SDI) transmitter. Camera video input signals are equalized, processed and output over coaxial connectors. 6G-SDI output is compliant to SMPTE ST2081-10 MODE 1 mapping, Dual Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping and 3G-SDI FHD output is compliant to SMPTE ST425-1 level A standards. Supported Video format: UHD (4MP active) output 2160/p30, 2160p29.97, 2160p25 FHD output 1080p60, 1080p59.94, 1080p50 TL4K1171 Overview Features FCB-EW9500 High Resolution Utilizing a 4M sensor and sharp lens achieve superior resolution and accurate image representation with the evolved AF/AE/ AWB functions even in low light environments. Combined with enhanced optical zoom achieve a high image quality from the Wide end to the Tele end.  High Sensitivity Through introduction of new cell structures and circuit technology, the series efficiently uses light, achieving twice the sensitivity compared to conventional image sensors. Consequently, clear images can be captured even during the night and in dark environments. Super Image Stabilizer Enables capturing of highly precise video with reduced blurring even in harsh environments with strong vibrations by greatly improving blur suppression and image stabilizer. The camera is during full HD or HD output equipped with the Super and Super modes. Applying a wide correction area using 4M pixels the camera series suppresses blurs from strong vibrations and rotational vibrations compared to conventional models. Super Suppresses strong vibrations with a wider correction area compared to conventional electronic vibration suppressors. Super + By employing a wider correction area than “Super,” “Super+” suppresses intense vibrations that cannot be suppressed with “Super.” Potential application: Shipboard, attachments for ITS surveillance, on bridges, drones, vehicles, etc. Starvis 1/1.8-type CMOS sensor The Sony FCB-9500H Sony blockcamera is equipped with an approximately 417 million- effective-pixel, 1/1.8-type high sensitive, AR-coated (anti-reflective coating) CMOS sensor. With a high spectral sensitivity value in near infrared to infrared, it is especially effective for security uses. Furthermore, the AR coating minimizes the ghost phenomenon and enables capturing of images without missing crucial information even during the night and in dark environments. 30x Enhanced Optical Zoom Using a compact lens designed for resolutions up to 8M the camera maximizes the coverage of the 4M sensor. The newly designed lens provides high resolution and low aberration, making it capable of capturing high resolution images that span from the Tele end from the screen center to the surrounding edges. There is no image deterioration using the 30x enhanced optical zoom. Experience full sharpness and dramatically reduced chromatic aberration in full HD output and also achieve images with sharp resolution during 4M output. Flare reduction with the new iris Diamond flares and ghosts that occur on lenses disrupts focusing and deteriorates the image quality. The new lens adopts 7 blades compared to the conventional 2 blades, improving this phenomenon by generating fine circular flares, and thus greatly improving image quality. Color image acquisition during ICR ON On conventional models, only black and white images are achieved while the IR cut filter was removed. The new ICR ON COLOR function enables the camera to capture shots with color even when the IR cut filter is removed. It is effective for color visibility in dark environments. The precision of color reproduction varies depending on the light source and brightness. Spot Focus · Spot AE · Spot AWB Enables functioning of AF, AE, and AWB only in specified areas within the screen. Enables independent specification of any rectangle of the entire screen divided in 6 x 8. For example, if the subject location is specified with Spot AE, enables capturing of images with Exposure effects reduced even if brightness changes occur outside the specified frame. Adjustable ROIs Screen divided in 6 x 8 Wide Dynamic Range (Wide-D) Wide-D mode is a function for dividing an image into several blocks for correcting blocked-up shadows and blown-out highlights in accordance with the intensity difference. It enables image acquisition in which portions ranging from dark to light can be recognized, even when capturing a subject with a large intensity difference that is backlit or includes extremely light regions of interest. Wide Dynamic Range Off Wide Dynamic Range On Sony FCB-EW9500H Specifications Specification FCB-EW9500H (4M · HDMI) Basic Features Image Sensor (Number of effective pixels) 1/1.8-type STARVISTM CMOS Sensor (Approx. 4.17M pixels)    Output Image Size (H x V) 2688x1512 *1 2560x1440*1 1920x1080, 1280x720   Signal System 2160p/60, 2160p/59.94, 2160p/50, 2160p/30, 2160p/29.97, 2160p/25, 1080p/60, 1080p/59.94, 1080p/50, 1080p/30, 1080p/29.97, 1080p/25, 1080i/60, 1080i/59.94, 1080i/50, 720p/60, 720p/59.94, 720p/50, 720p/30, 720p/29.97, 720p/25   Minimum Illumination (50%, High Sensitivity Mode ON) ICR-Off mode: 0.009 lx (Shutter Speed: 1/30 s), 0.0012 lx (Shutter Speed: 1/4 s or 1/3 s) ICR-On mode: 0.00008 lx (Shutter Speed: 1/30 s), 0.000005 lx (Shutter Speed: 1/4 s or 1/3 s, 30%)   Minimum Illumination (50%, High Sensitivity Mode OFF) ICR-Off mode: 0.09 lx (Shutter Speed: 1/30 s), 0.012 lx (Shutter Speed: 1/4 s or 1/3 s) ICR-On mode: 0.00063 lx (Shutter Speed: 1/30 s)   Recommended Illumination 100 lx to 100,000 lx   Image S/N  Wide end to Tele end - 4.8 s (Focus Tracking ON), 2.9 s (Focus Tracking OFF) Wide end to Digital 12x tele - 6.1 s (29.97p/59.94p), 6.4 s(25p/50p)      Gain Auto/Manual (0 dB to 50.0 dB), 0 to 28 steps   Shutter Speed 1/1 to 1/10000 s, 22 steps   Sync System Internal   Exposure Control 0 dB to ± 10.5 dB, 15 steps   Backlight Compensation Yes   Gamma Standard / Straight gamma   Aperture Control 16 steps   White Balance Auto, ATW, Indoor, Outdoor, One Push WB, Manual WB, Outdoor Auto, Sodium Vapor Lamp (Fix/Auto/Outdoor Auto), Spot AWB   AE (Auto Exposure Mode) Full Auto, Manual, Priority mode (shutter/iris), EV compensation, Spot AE, Slow AE   Zoom 30x Enhanced Optical Zoom 36x StableZoom and 12x Digital Zoom  - StableZoom increases the magnification by combining optical zoom and digital zoom  - FCB-EW9500H: For 1080p, 1080i, and 720p only.   Lens (wide to tele) f = 6.5 mm to 162.5 mm, F1.6 to 4.8   Zoom Mode Standard Mode / Variable Mode / Direct Mode   Zoom Movement Speed Wide end to Tele end - 4.8 s (Focus Tracking ON), 2.9 s (Focus Tracking OFF) Wide end to Digital 12x tele - 6.1 s (29.97p/59.94p), 6.4 s(25p/50p) Digital wide to Digital 12x tele - 1.4 s (29.97p/59.94p), 1.6 s (25p/50p)   Focusing System Auto Focus (Normal AF, Interval AF, Zoom Trigger AF [Sensitivity: normal, low]), Manual (Standard, Variable, Direct), One Push Trigger, Full Scan One Push Trigger, Near Limit, ICR-on Correction, Spot Focus   Focus Movement Time ∞ to Near: 1.4 s   Horizontal Viewing Angle 58.1° to 2.3°   Minimum Object Distance (wide end to tele end) 100 mm to 1200mm Camera Features Auto ICR Yes   Wide Dynamic Range (Wide-D) Yes   Visibility Enhancer Yes   Defog Yes (low/mid/high)   Noise Reduction Yes (3D + 2D / Independent setting (3D, 2D))   Progressive Scan Mode Yes   Image Stabilization Yes: Super image stabilizer (Super / Super+ FCB-EW9500H: For 1080p, 1080i, and 720p only.)   Spot Light Avoidance Yes   Motion Detection Yes   Privacy Zone Masking Yes   Alarm Yes   Slow AE Response Yes   Picture Effects Black White (Monochrome Image)   Picture Freeze Yes   Electronic-Flip (E-FLIP) Yes   Mirror Image Yes   Slow Shutter Yes   Temperature Readout Yes   Title Display Yes (20 characters / line, max. 11lines)   Camera Mode Display Yes (English) Interface Video Output Digital : Y/Pb/Pr 4:2:2 (HDMI) Y:8bit, C:8bit RGB 4:4:4 (HDMI) R:8bit G:8bit B:8bit   Camera Control Interface VISCA protocol (CMOS 3.3V Level, 5.5V tolerance); Baud Rate : 9.6 kbps, 19.2 kbps, 38.4 kbps, 115.2 kbps, Stop bit: 1 bit General Power Requirements 7.0 V to 12.0 V DC   Power Consumption 4.6 W (When motor operates: 6.3W)   Operating Temperature "-5 °C to +60 °C (23 °F to +140 °F)"   Storage Temperature "-20 °C to +60 °C (–4 °F to +140 °F)"   Operating Humidity 20% to 80% (Absolute humidity: 36 g/m3)   Storage Humidity 20% to 95% (Absolute humidity: 36 g/m3)   Dimensions (W x H x D) 56.0 x 64.0 x 125 mm (2 1/4 × 2 5/8 × 5 in.)   Mass Approx. 439 g (15 oz.) FCB-9500 Series Promotion Block Camera Movie

Price on request

AIVION Interfaces

SL4651 | Analog HD-TVI
SL4651 is a small form factor HD-TVI/AHD analog HD video transmitter for Block Cameras. Camera LVDS video input signals are demultiplexed, processed and output over a MCX coaxial connector. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B-0200 cable kit is included and contains 30wire micro coaxial cable for connecting SL4651 to the camera as well as 10wire power supply and serial control cable harness. Features: High Definition analog HD-TVI or AHD output 1080p30 /25 Hz 720p60 /50 Hz Small form factor Small form factor 55mm x 36mm Camera Control RS232 and TTL level serial control interface RS485 camera control interface (optional) Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Applications Full HD integrated cameras with analog HD YPbPr output requirements Industrial, medical, security, law enforcement Download SL4651 Datasheet V2.2.0 SL4651 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 4.08W (MP1110M-VC camera lens steady +SL4651) PD = 4.56W (FCB-EV7520A camera lens steady +SL4651) PSL4651 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4561 is RoHS compliant (2002/05/EG and 2011/65/EU) SL4651 PCB Connectors J6 HD-TVI/AHD output connector Samtec MCX7-J-P-H-RA-TH1 J5 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) SL4651 PCB Outline Onboard Mode Switch: Switch #1 SL4651 Video Output Mode: OFF=HD-TVI, ON=AHD Switch #2 Camera Monitoring Mode Adjust: OFF=No change, ON*=Force 1080p30 *SL4651 onbaord microcontroller adjusts camera video output setting to 1080p30 if switch #2 is in ON position. Checking switch #2 is done once during SL4651 boot cycle. Changing switch #2 position during board operation has no effect. Also switch #1 must be preset before power is applied to SL4651. SL4651 | Production Kit Partnumber Content SL4651 HD-TVI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n SL4651-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector

Price on request

SL4655 | FHD LVDS to analog YPbPr
SL4655 is a small form factor analog YPbPr FHD video transmitter. Camera LVDS video input signals are demultiplexed, processed, converted to analog and output over 6pin board to wire connector. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232, 3.3V TTL or RS485(optional) level. TLCK-B5 cable kit is included and contains 30wire micro coaxial cable for connecting SL4655 to the camera as well as 10wire power supply and serial control cable harness and a 6wire cable harness for the video output. Features: High Definition analog HD-YPbPr output 1080p30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25 Hz Small form factor Small form factor 55mm x 36mm Camera Control RS232 and TTL level serial control interface RS485 camera control interface (optional) Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Applications Full HD integrated cameras with analog HD YPbPr output requirements Industrial, medical, security, law enforcement Download SL4655 Datasheet V1.2.0 SL4655 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 4.08W (MP1110M-VC camera lens steady +SL4655) PD = 4.56W (FCB-EV7520A camera lens steady +SL4655) P SL4655 = 1.28W (typ.) (12V DC supply, 1920x1080@30fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% SL4565 is RoHS compliant (2002/05/EG and 2011/65/EU) SL4655 PCB Connectors J5 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J7 YPbPr Video Output JST SM6B-SRSS-TB Pin Signal 1 Y signal output 2 GND (0V) 3 Pb signal output 4 GND (0V) 5 Pr signal outpu 6 GND (0V) SL4655 PCB Outline SL4655 | Production Kit Partnumber Content SL4655 FHD LVDS to analog YPbPr Board TLCK-B5 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K06-150 6 pin flying leads cable for YPbPr, length 15cm SL4655-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector

Price on request

TL3K7052 | WQHD HDMI
The TL3K7052 is a WQHD HDMI output video transmitter for block cameras from AIVION. It connects to the digital video interface of the block cameras and support several progressive and interlace HDTV formats. Features: One HDMI Output 1440p30 /25 Hz 1080p30 /25 Hz 720p30 /25Hz Small Form Factor Small form factor 46mm x 44mm Camera Control RS232 level serial camera control interface TTL level serial control interfac Temperature Range Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Temperature monitoring with alert function Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Power 9V to 12V DC regulated (13V DC absolute maximum) Download TL3K7052 V1.0.0 Datasheet TL3K7052 Block Diagram Power Input: 9V to 12V DC regulated (13V DC absolute maximum) Power consumption (incl. camera) 5.3W (cam motors inactive) Characteristics: PD = 5.6W (FCB-EV7520A camera lens steady +TL7055) PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/140°F - Humidity: 20%-80% TL3K7052 PCB Connectors J3 LVDS Video In 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J8 HDMI Camera Interface Kycon KDMIX_FS1V_WS or equivalent J1 Power and RS232/TTL Control IF JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera for reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) TL3K7052 PCB Outline Test Pattern Generator TL3K7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL3K7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL3K7052 power off and on again Note: For TPG operation on TL3K7052, the camera must be connected. TL3K7052 | Production Kit Partnumber Content TL3K7052 WQHD HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm TL3K7052-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

Price on request

TL4K1152 | 4K HDMI
The TL4K1152 is a small form factor digital serial video transmitter from AIVION. Small form factor with an attractive price are some of the main features of the TL4K1152. It supports the new trend setting Sony block camera FCB 4K Series from Sony via an HDMI output. Camera control can be managed through an RS232 port. Via the available USB2 interface firmware updates can be obtained. Features: One HDMI 1.4b video output Up to 2160p30 UHD, FHD, HD video format support Integrated input signal equalizer Ultra high speed 3.4Gbps cable driver Small Form Factor Small form factor 46mm x 30mm Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control IF Temperature Range Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Compliance RoHS compliant (2002/05/EG and 2011/65/EU) Power Supply voltage 7V to 12V DC regulated Ultra low power - 150mW@8V supply voltage only Download TL4K1152 V2.0.0 Datasheet TL4K1152 Block Diagram Power Input: 7V to 12V DC regulated supply input voltage range Characteristics: PD = 3.05W (FCB-ER8300 lens steady +TL4K1152) PTL4K1152 = 150mW (typ.) (8V DC supply, 3840x2160@29.97fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1152 PCB Connectors J4 LVDS Video In 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J2 HDMI Camera Interface J1 Power and RS232/TTL Control IF Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V) 8 RXD_TTL (serial IF receive 3.3V) 9 RXD_232 (serial IF receive RS232) 10 TXD_232 (serial IF transmit RS232) J3 USB connector do not connect (for FCB-ER8300 firmware updates only). USB connector is no more assembled for revision B boards. TL4K1152 PCB Outline TL4K1152 | Production Kit Partnumber Content TL4K1152 HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1152-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

Price on request

TL4K1161 | Dual Link 3 Gbps UHD-SDI
The TL4K1161 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed and output over coaxial connectors. Dual Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping, FHD output is compliant to SMPTE ST425-1 level A standards. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B-0200 cable kit is available as accessory. Features: SDI Video Output MCX 75 Ohm straight coaxial connectors Resolution up to 3840x2160p @ 30fps Dual Link 3G-SDI output of UHD formats 3G-SDI output of FHD formats 1.5G-SDI output of HD formats Automatic format detection Small Form Factor Small form factor 60mm x 46mm Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control IF Temperature Range and Power Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Application 4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530, FCB-ER8300, FCB-ES8230 and FCB-EW9500H camera blocks Industrial, medical, security, law enforcement, video production Download TL4K1161 V2.1.0 Datasheet TL4K1161 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 6.72W typ. (FCB-ER8300 lens steady +TL4K1161) P TL4K1161 = 3.72W (typ.) (12V DC supply, 3840x2160@25fps, TA = 25°C, Humidity = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1161 PCB Connectors J7 SDI output connector Link 1 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J8 SDI output connector Link 2 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J1 Power and Control IF Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 HDMI Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. TL4K1161 PCB Outline TL4K1161 | Production Kit Partnumber Content TL4K1161 Dual Link 3G-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1161-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws 2 x CK-MCX-BNC 2 MCX to BNC connector cable 

Price on request

TL4K1171 | 6 Gbps UHD-SDI & 3 Gbps Dual Link UHD-SDI Interface
The TL4K1171 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed, and output over coaxial connectors. 6G-SDI output is compliant to SMPTE ST2081-10 MODE 1 mapping, Dual Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping and 3G-SDI FHD output is compliant to SMPTE ST425-1 level A standards. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B cable kit is available as accessory. Features: SDI Video Output Native signal processing for highest image quality MCX 75 Ohm straight coaxial connectors Resolution up to 3840x2160p @ 30fps 6G-SDI output of UHD formats Dual Link 3G-SDI output of UHD formats 3G-SDI output of FHD formats Automatic format detection Small Form Factor Small form factor 60mm x 46mm Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control interface Temperature Range and Power Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Application 4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530, FCB-ER8300, FCB-ES8230 and FCB-EW9500H camera blocks Industrial, medical, security, law enforcement, video production Download TL4K1171 V1.0.1 Datasheet TL4K1171 Block Diagram Power Input: 9V to 12V DC (12.5V DC max.) regulated supply input voltage range Characteristics: PD = 7.0W typ. (FCB-ER8530 lens steady +TL4K1171) P TL4K1171 = 3.9W (typ.) (12V DC supply, 3840x2160@29.97fps, TA = 25°C, Humididty = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1171 PCB Connectors J1 Power and Control IF (JST SM10B-SRSS-TB) Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J3 External Sync (JST SM08B-SRSS-TB) for use with FCB-ER8550 only Pin Signal 1 GND (0V) 2 External Sync Loop Out 3 GND (0V) 4 ACC_LED (Output signal from FCB-ER8550) 5 GND (0V) 6 External Sync Input 7 GND (0V) 8 SYNC_LOCK (Output signal from FCB-ER8550) J4 HDMI Input (KEL USL00-30L-A) 30wire microcoax connector for FCB-ER8xxx and FCB-EW9500H. Use 30wire micro coaxial cable supplied with cable kit. J6 Board feature extension connector Contact us for further notice J7 + J8 SDI output connector (Samtec MCX7-J-P-H-ST-TH1) Mode J7 J8 UHD 6GbpsUHD mode selection by switch#2 No output 6G-SDI UHD 3GbpsUHD mode selection by switch#2 Link1 of Dual Link 3G-SDI Link2 of Dual Link 3G-SDI FHDFHD operation requires camera to be set to 1080p60, 1080p59.94 or 1080p50 GND (0V) 3G-SDI (same signal as J7) Board Config Switch   Switch# OFF ON 1 RS232 based camera control 3.3V TTL based camera control 2 6G-SDI UHD Output Mode DL 3G-SDI UHD Output Mode 3 Keep OFF Reserved 4 Keep OFF Reserved TL4K1171 PCB Outline TL4K1171 | Production Kit Partnumber Content TL4K1171 6 Gbps / Dual Link 3Gbps UHD-SDI Interface Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1171-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws 2 x CK-MCX-BNC MCX to BNC connector cable

Price on request

TL4K1261 | Dual Link 3 Gbps UHD-SDI (PCOC Feature)
The TL4K1261 is a small form factor serial digital video (SDI) transmitter from AIVION with Power and Control over Coaxial Cable. Camera video input signals are equalized, processed, and output over straight DIN7A(10.23) connectors. Dual Link 3G-SDI output compliant to SMPTE ST425-3, 2si mapping, FHD output compliant o SMPTE ST425-1 level A Camera control is accomplished by a transparent full-duplex communication channel. The physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B cable kit is included and contains a 30wire micro coaxial cable for connecting TL4K1261 to FCB-ER8300 as well as a 10wire power supply and serial control cable harness. Features: SDI Video Output DIN7A (10.23) 75 Ohm straight coaxial connectors Resolution up to 3840x2160p @ 30fps Dual Link 3 Gbps UHD-SDI Transmitter Dual Out 3/1.5 Gbps FHD-SDI Transmitter 3G-SDI output of FHD formats 1.5G-SDI output of HD formats Automatic format detection PCOC Power and Control over Coaxial Cable 100m Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control IF Temperature Range and Power Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Application 4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530 and FCB-ER8300 4K camera blocks Industrial, medical, security, law enforcement, video production Download TL4K1161 V1.1.0 Datasheet TL4K1261 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 6.72W typ. (FCB-ER8300 lens steady +TL4K1261) P TL4K1261 = 3.62W (typ.) (12V DC supply, 3840x2160@29.97fps, TA = 25°C, Humidity = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1261 PCB Connectors J7 SDI output connector Link 1 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J8 SDI output connector Link 2 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J1 Power and Control IF Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. TL4K1261 PCB Outline TL4K1261 | Production Kit Partnumber Content TL4K1261 Dual Link 3G-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1261-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws 2 x TL-EVK-DIN-BNC-1 2 Connector cables with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter 

Price on request

TL6032 | USB 3.0 Horizontal Micro B Interface
The TL6032 interface is a HDTV USB 3.0 compliant video streaming capture solution from AIVION. As no analog to digital conversion is done on these modules, excellent output image quality is guaranteed. Features: USB 3.0 Video Output Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format 1920x1080p @ 25Hz, 29.97Hz, 30 Hz 1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer Small Form Factor Small form factor 45mm x 40mm USB Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported) Host computer must run a UVC capable operating system Parallel up- and downstream of camera control and status data is possible (USB CDC) Power Full USB bus powered camera solution possible depending on camera Power supply voltage for camera is generated onboard Allows an external power supply Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Temperature Range Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Download TL6032 V2.0.0 Datasheet TL6032 Block Diagram Power Input: 5V DC from USB3 port Characteristics: Power consumption (FCB-EV75xx + TL6035) 5.6W Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive) Power consumption TL6035: 2.7W/540mA@5V DC (max.) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80% TL6032 PCB Connectors J6 USB3 microB connector Horizontal J2 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. J7 External Power Supply Pin Signal 1 Input voltage 5V to 7V DC 2 Input voltage 5V to 7V DC 3 System reset, pull to GND for reset 4 GND (0V) 5 GND (0V) J9 RS232 UART Connector Pin Signal 1 to 7 do not connect 8 GND 9 RXD (host to camera) 10 TXD (camera to host) TL6032 PCB Outline Camera Power Camera supply voltage is generated on TL6032 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera. NOTE: USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6032. TL6032 EXTERNAL POWER OPTION: TL6032 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6032 for the camera supply boost converter only. All other electronic devices on TL6032 are always powered from USB3 port. No adjustments on TL6032 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power. Host (PC) - Device Communication TL6032 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6032 via a serial communication channel (USB UART). Connecting the TL6032 to the Host PC Operating System Support TL6032 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems: Windows 7 (32 and 64bit) Windows 8.1 (32 and 64bit) Windows 10 (64bit, version 1511) Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information. Controlling TL6032 from the Host PC via USB UART TL6032 supports the USB UART functionality. FCB cameras connected to TL6032 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1). TL6032 | Production Kit Partnumber Content TL6032 USB 3.0 Board TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL6032-EXT | Evaluation Extension Partnumber Content EK-PA1100-USB Power supply and control interface board PS-TE10A05 5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter TL-EVK-BRA Bracket and screws TL-EVK-USB3-A-MICROB USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector

Price on request

TL6035 | USB 3.0, Vertical Micro B Connector
The TL6035 USB 3.0 interface board from AIVION is a tiny and easy to use HDTV USB3.0 video capture interface for the block cameras. The module receives digital video signals and sends UVC (USB Videl Class) compliant data packets to a connected host computer. Our compact TL6035 module enables the design of small camera systems that need only a single connection between camera and PC. Video stream, control data and power will be connected by a USB 3.0 cable. For camera blocks that need more than 900 mA during startup a Y-cable is required. Features: USB 3.0 Video Output Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format 1920x1080p @ 25Hz, 29.97Hz, 30 Hz 1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer Small Form Factor Small form factor 45mm x 40mm USB Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported) Host computer must run a UVC capable operating system Parallel up- and downstream of camera control and status data is possible (USB CDC) Power Full USB bus powered camera solution possible depending on camera Power supply voltage for camera is generated onboard Allows an external power supply Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Temperature Range Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Datasheet TL6035 V2.0.0 Application Note TL6035 TL6035 Block Diagram Power Input: 5V DC from USB3 port Characteristics: Power consumption (FCB-EV75xx + TL6035) 5.6W Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive) Power consumption TL6035: 2.7W/540mA@5V DC (max.) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80% TL6035 PCB Connectors J6 USB3 microB connector Vertical J2 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. J7 External Power Supply Pin Signal 1 Input voltage 5V to 7V DC 2 Input voltage 5V to 7V DC 3 System reset, pull to GND for reset 4 GND (0V) 5 GND (0V) J9 RS232 UART Connector Pin Signal 1 to 7 do not connect 8 GND 9 RXD (host to camera) 10 TXD (camera to host) TL6035 PCB Outline Camera Power Camera supply voltage is generated on TL6035 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera. NOTE: USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6035. TL6035 EXTERNAL POWER OPTION: TL6035 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6035 for the camera supply boost converter only. All other electronic devices on TL6035 are always powered from USB3 port. No adjustments on TL6035 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power. Host (PC) - Device Communication TL6035 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6035 via a serial communication channel (USB UART). Connecting the TL6035 to the Host PC Operating System Support TL6035 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems: Windows 7 (32 and 64bit) Windows 8.1 (32 and 64bit) Windows 10 (64bit, version 1511) Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information. Controlling TL6035 from the Host PC via USB UART TL6035 supports the USB UART functionality. FCB cameras connected to TL6035 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1). TL6035 | Production Kit Partnumber Content TL6035 USB 3.0 Vertical Micro B USB Board TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL6035-EXT | Evaluation Extension Partnumber Content EK-PA1100-USB Power supply and control interface board PS-TE10A05 5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter TL-EVK-BRA Bracket and screws TL-EVK-USB3-A-MICROB USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector

Price on request

TL6636 | USB 3.0, Vertical Micro B Connector (Trigger)
The TL6636 USB 3.0 interface board with trigger functionality from AIVION is tiny and easy to use HDTV USB3.0 video capture interface for the block cameras. The module receives digital video signals and sends UVC (USB Videl Class) compliant data packets to a connected host computer. Our compact TL6636 module enables the design of small camera systems that need only a single connection between the camera and PC. Video stream, control data and power will be connected by a USB 3.0 cable. For camera blocks that need more than 900 mA during startup, a Y-cable is required. Features: USB 3.0 Video Output Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format 1920x1080p @ 25Hz, 29.97Hz, 30 Hz 1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer Trigger Real-time external trigger input for MP2030M-GS global shutter camera block Single LVDS data format provided by Tamron camera blocks USB Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported) Host computer must run a UVC capable operating system Parallel up- and downstream of camera control and status data is possible (USB CDC) Power Full USB bus powered camera solution possible depending on camera Power supply voltage for camera is generated onboard Allows an external power supply Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Temperature Range Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Download TL6636 V2.0.0 Datasheet TL6636 Block Diagram Power Input: 5V DC from USB3 port Characteristics: Power consumption (MP2030M-GS + TL6636) 7.65W (cam motors inactive) Power consumption (MP2030M-GS + TL6636) 9.3W (boot cyle and cam motors active) Power consumption TL6636: 2.7W/540mA@5V DC (max.) Power consumption value conditions: Camera monitoring mode set to 1080p30 Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80% TL6636 PCB Connectors J6 USB3 microB connector Vertical J2 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. J7 External Power Supply Pin Signal 1 Input voltage 5V to 7V DC 2 Input voltage 5V to 7V DC 3 System reset, pull to GND for reset 4 GND (0V) 5 GND (0V) J9 RS232 UART Connector Pin Signal 1 External trigger pulse* input, 3.3V max. Active high trigger pulse duration must be 1us minimum. Trigger pulse input has a 10kohms pullup resistor 2 Trigger demo mode select input**, 3.3V max. Trigger mode select input has a 10kohms pulldown resistor 3 do not connect 4 Trigger response output 5 3.3V output (20mA max.) 6 do not connect 7 do not connect 8 GND 9 RXD (host to camera) 10 TXD (camera to host) TL6636 PCB Outline Camera Power Camera supply voltage is generated on TL6636 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera. NOTE: USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3.0 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3.0 output power is sufficient or not. This is in the sole responsibility of the user of TL6636. In case the host computer provides a USB3.1 port, it is recommended to use this one instead of a USB3.0 port. TL6636 EXTERNAL POWER OPTION: TL6636 allows to use an external power supply in case USB3 power of the computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6636 for the camera supply boost converter only. All other electronic devices on TL6636 are always powered from USB3 port. No adjustments on TL6636 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power. EXTERNAL POWER USE PER CAMERA MODEL: MP2030M-GS: Recommended, should be used MP1010M-VC: Not required but can be used MP1110M-VC: Not required but can be used Host (PC) - Device Communication TL6636 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6636 via a serial communication channel (USB UART). Connecting the TL6636 to the Host PC Operating System Support TL6636 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems: Windows 7 (32 and 64bit) Windows 8.1 (32 and 64bit) Windows 10 (64bit, version 1511) Driver Requirements Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file. Video Application on Host PC Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information. Controlling TL6636 from the Host PC via USB UART TL6636 supports the USB UART functionality. FCB cameras connected to TL6636 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1). Real-Time external Trigger Operation NOTE: EXTERNAL TRIGGER IS AVAILABLE WITH MP2030M-GS ONLY. Tamron’s MP2030M-GS global shutter block camera module allows for real- time triggered still image capture. Refer to MP2030M-GS technical manual provided by Tamron for details on real-time triggered still image capture operation. TL6636 USB3 full HD video streamer provides a trigger mode input for selecting one out of two available trigger modes. Mode 1 (default, pin2/J9 0V or open): External direct trigger Trigger pulse input on pin1/J9 is glitch filtered and driven to MP2030M-GS trigger input po Mode 2 (pin2/J9 3.3V): Automatic periodic trigger (demo mode) After selecting and activating trigger mode at MP2030M-GS by the related VISCA commands, the automatic trigger period is set to 1.5s. In this demo mode the camera takes an image every 1.5s (approx.). TL6636 | Production Kit Partnumber Content TL6636 USB 3.0 Vertical (Trigger) TLCK-B 1. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 2. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 3. TLCK-FL05-150 5 pin flying leads cable for external power, length 15cm TL6636-EXT | Evaluation Extension Partnumber Content EK-PA1100-USB Power supply and control interface board PS-TE10A05 5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter PTL-EVK-BRA Bracket and screws TL-EVK-USB3-A-MICROB USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector

Price on request

TL7050 |  Dual HD-SDI and HDMI Interface
The TL7050 Dual 3G/HD-SDI and DVI(HDMI) Output Video Transceiver module from AIVION connect to the digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One HDMI Output HDMI connector (Kycon KDMIX_FS1V_WS) 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Video input and Compliance Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7050 V 2.5.0 Datasheet TL7050 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Characteristics: Power consumption TL7050: 260mA @ 12V DC (typ.) Operating and Storage Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7050 PCB Connectors J8 HDMI connector Kycon KDMIX_FS1V_WS J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7050 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output TL7050 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7050 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7050 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7050 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7050 Analog Video Output TL7050 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7050, the camera is also automatically powered. During power up all functions on TL7050, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7050. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7050 | Production Kit Partnumber Content TL7050 HDMI-HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7050-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

Price on request

TL7051 | Dual HD-SDI Interface
The TL7051 Dual 3G/HD-SDI Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and supports several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7051 Revision D V.3.0.0 Datasheet TL7051 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7051 PCB Connectors J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7051 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7051 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND TL7051 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low ( < 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7051 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7051 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7051 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7051 Analog Video Output TL7051 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7051, the camera is also automatically powered. During power up all functions on TL7051, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7051. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7051 | Production Kit Partnumber Content TL7051 3G-SDI/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7051-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable

Price on request

TL7052 |  HDMI Interface
The TL7052 DVI(HDMI) Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera One HDMI Output HDMI connector (Kycon KDMIX_FS1V_WS) 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7052 V 2.4.0 Datasheet TL7052 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7052 PCB Connectors J8 HDMI connector Kycon KDMIX_FS1V_WS J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7052 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 Analog component YPbPr and CVBS output Requires TL7052 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND J4 24pin FFC Connector Power, Reset, Serial Control IF, analog Video TL7052 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7052 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7052 Analog Video Output TL7052 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7052, the camera is also automatically powered. During power up all functions on TL7052, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7052. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7052 | Production Kit Partnumber Content TL7052 HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7052-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

Price on request

TL7055 | 3G-SDI & analog YPbPr Interface
The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector. Features: One 3G-SDI/HD-SDI Output MCX connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One Analog YsPbPr Output 8pin board to wire connector Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV Pb, Pr 0,7Vpp into 75 ohms 1080p60 /59.94 /50 /30 /29.97 /25 Hz 720p60 /59.94 /50 Hz Camera Control RS232 level serial camera control interface Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface. Temperature Range and Power Operating ambient temperature range -10°C to +60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Small form factor & Compliance Small form factor 46mm x 44mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements Industrial, medical, security, law enforcement Download TL7055 Datasheet TL7055 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 5.6W (FCB-EV7520A camera lens steady +TL7055) PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%) Operating and Storage Conditions: Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU) TL7055 PCB Connectors J8 SDI Video Output Samtec MCX7-J-P-H-ST-SM1 J7 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J2 Power & Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 Do not connect 8 Do not connect 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 YPbPr Video Output JST SM08B-SRSS-TB Pin Signal 1 HSync 2 VSync 3 GND (0V) 4 Pb signal output 5 GND (0V) 6 Ys signal output 7 GND (0V) 8 Pr signal output TL7055 PCB Outline Board Operation: TL7055 TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal. The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes). The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as 7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels. In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode. TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera. When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details). The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055. Test Pattern Generator (TPG) mode: TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default. TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards. The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control. The following VISCA commands are available for TPG control (all codes as hex values): TPG activation: 87 01 00 24 01 08 0A FF TPG deactivation: 87 01 00 24 01 08 06 FF TPG pattern type 100% color bar: 87 01 00 24 04 00 04 FF TPG pattern type multi pattern with moving block: 87 01 00 24 04 00 00 FF TPG video standard: 87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50 pq = 19 for 720p60 TL7055 | Production Kit Partnumber Content TL7055 3G-SDI & analog Board TLCK-B6 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n 3. TLCK-K08-150 8wire cable harness for the analog YsPbPr video output TL7055-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB-SA USB to serial adapter CK-MCX-BNC MCX to BNC connector cable

Price on request

TL7070 | optical fiber (Transmitter)
+ Digital LVDS video input from camera+ 1080i, 1080p and 720p output standard support+ 25Hz, 29.97Hz, 30Hz, 50Hz, 59.94Hz and 60Hz frame rates+ Automatic camera and video standard detection+ Optical 3G/HD-SDI output based on SFP compatible transmitter+ Optical transmitter 1310nm/10km/LC for SMF included+ BNC + MCX coax 3G/HD-SDI outputs+ HD-SDI outputs compliant to SMPTE425M/424M/292M/274M/296M+ DVI (HDMI connector) video output+ Native digital signal processing chain for best image quality (no scaling)+ Breakout of camera analog HDTV YPbPr and CVBS video+ Dual serial control interface (RS232 or 3.3V TTL)+ Supply voltage: 7V to 12V DC regulated (5V only when used with FCB-SE600)

Price on request

TL7071 | optical fiber (Receiver)
+ Optical 3G/HD-SDI input based on SFP compatible receiver+ Optical SFP receiver 1260nm-1620nm/10km/LC for SMF included+ Input compliant to SMPTE297M-2006 serial optical 3G/HD video standards + Automatic video standard detection+ Input signal jitter removal+ Format conversion for DVI(HDMI) RGB output+ Reclocked 3G/HD-SDI BNC + MCX coax outputs+ 3G/HD-SDI outputs compliant to SMPTE425M/424M/292M/274M/296M+ SMPTE425M level A, mapping structure 1+ Selectable serial control interface (RS232 or 3.3V TTL)+ Supply voltage: 5V to 12V DC regulated

Price on request

TL7075-TL7076 | one fiber line solution for camera control and video, transmit
TL7076+ Optical receiver compliant to SMPTE297M-2006 serial optical 3G/HD video standard + Automatic video standard detection+ Input signal jitter removal+ SFP transceiver λTX=1550nm, SMF/LC included+ Reclocked 3G/HD-SDI BNC + MCX coax outputs, format conversion for DVI(HDMI) RGB output + Dual serial control interface (RS232 or 3.3V TTL)+ Supply voltage: 7V to 12V DC regulatedTL7075+ Supports all Sony FCB-EV, all FCB-EH and FCB-SE600 camera models + Digital LVDS video input from camera+ Optical 3G/HD-SDI output compliant to SMPTE297M-2006+ SFP transceiver λTX=1310nm, SMF/LC included+ Local BNC coax, MCX coax and DVI (HDMI connector) 3G/HD-SDI outputs

Price on request

TL8651 | HD-SDI Interface
The AIVION TL8651 outputs serial digital video (SDI) up to 1080p60. It connects to the digital video interface of the block cameras and supports several progressive and interlace HDTV formats. Features: One 3G-SDI/HD-SDI Output Right angle DIN7A connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Board Side Mount The TL8651 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras. Tamron MP1010M-VC Tamron MP1110M-VC Camera Control RS232 and TTL level serial control interface Temperature Range and Power Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9.5V to 12V DC regulated Small form factor & Compliance Small form factor 60mm x 36mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Industrial, medical, security, inspection, ROV and Security Download TL8651 Datasheet TL8651 Block Diagram Power Input: 9.5V to 12V DC regulated supply input voltage range Power consumption (MP1110M-VC + TL8651) 4.7W (cam motors inactive) Power consumption value conditions: Power 12V DC, video mode 1080p60 Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80% Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80% TL8651 PCB Connectors J2 KEL USL00-30L-A Camera IF, use supplied 30wire micro coaxial cable only J4 3G/HD-SDI output KEL USL00-30L-A Default type: CEI C-SX113 (DIN7A / 1.0/2.3 coax system) J3 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC In 2 DC In 3 GND 4 GND 5 Reset / Shut Down, pull to GND to reset/shut down TL7650 and camera for reset, pull to GND for one second or longer 6 GND 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 CVBS Output JST SM03B-SRSS-TB Pin Signal 1 GND 2 CVBS analog video output 3 GND (0V) CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details. In NTSC or PAL mode, there will be no SDI output signal available from TL8651. CVBS output connector J5 is available on Rev.B boards from September 26, 2018. TL8651 PCB Outline TL8651 | Production Kit Partnumber Content TL8651 3G/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL8651-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-DIN-BNC-1 Connector cable with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter

Price on request

TL8652 | HDMI Interface
The TL8652 HDMI Output Video Transceiver module from AIVION connect to the digital video interface of the block cameras and support several progressive and interlace HDTV formats. TL8652 outputs HDMI up to 1080p60. Features: HDMI 1.4 output RGB444 or YCbCr422 colour format selectable 1080p60 /50 /30 /25 Hz 1080i60 /50 Hz 720p60 /50 Hz Board Side Mount The TL8652 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras. Tamron MP1010M-VC Tamron MP1110M-VC Camera Control RS232 and TTL level serial control interface Integrated USB2 UART for camera control Temperature Range Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Small form factor & Compliance Small form factor 61mm x41mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Power USB powered 5V DC Download TL8652 V2.2.0 Datasheet TL8652 Block Diagram Power Input: 5V DC over USB2 micro connector (USB3 host port or powered USB3 hub required) Power consumption (MP1010M-VC + TL8652) 4.5W/900mA (cam motors inactive) Power consumption TL8652: 1.5W, 300mA @ 5V DC (typ.) Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80% Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80% TL8652 PCB Connectors J6 KEL USL00-30L-A Camera IF, use supplied 30wire micro coaxial cable only J3 HDMI micro connector J2 USB2 micro connector J1 Reset and RS232 Control IF JST SM10B-SRSS-TB Pin Signal 1 Do not connect 2 Do not connect 3 GND 4 GND 5 Reset / Shut Down, pull to GND to reset/shut down TL8652 and camera for reset, pull to GND for one second or longer 6 GND 7 Do not connect 8 Do not connect 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J7 CVBS Output JST SM03B-SRSS-TB Pin Signal 1 GND 2 CVBS analog video output 3 GND (0V) CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details. In NTSC or PAL mode, there will be no HDMI output signal available from TL8652/A. TL8652 PCB Outline TL8652 | Production Kit Partnumber Content TL8652 HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL8652-EXT | Evaluation Extension Partnumber Content TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector Driver Installer Package and Cypress USB-Serial Driver Installation Guide for the USB2 UART Chip are online available. TL-EVK-HDMI-MICRO-D High Speed HDMI Cable 1 with HDMI-A 19 and 1 HDMI Micro-D 19 pin male connector 

Price on request

TL8656 | HD-SDI Interface with Trigger and PCOC
The AIVION TL8656 outputs serial digital video (SDI) up to 1080p60 with Power and Control over Coaxial Cable and an external Trigger. It connects to the digital video interface of the block cameras and supports several progressive and interlace HDTV formats. Features: One 3G-SDI/HD-SDI Output Right angle DIN7A connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Board Side Mount The TL8656 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras. Tamron MP1010M-VC Tamron MP1110M-VC Camera Control RS232 and TTL level serial control interface Power and Control over Coaxial Cable Ext. Trigger Temperature Range and Power Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9.5V to 12V DC regulated Small form factor & Compliance Small form factor 60mm x 36mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Industrial, medical, security, inspection, ROV and Security Download TL8656 Datasheet TL8656 Block Diagram Power Input: 9.5V to 12V DC regulated supply input voltage range Power consumption (MP1110M-VC + TL8656) 4.7W (cam motors inactive) Power consumption value conditions: Power 12V DC, video mode 1080p60 Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80% Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80% TL8656 PCB Connectors J2 KEL USL00-30L-A Camera IF, use supplied 30wire micro coaxial cable only J4 3G/HD-SDI output KEL USL00-30L-A Default type: CEI C-SX113 (DIN7A / 1.0/2.3 coax system) J3 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC In 2 DC In 3 GND 4 GND 5 Reset / Shut Down, pull to GND to reset/shut down TL7650 and camera for reset, pull to GND for one second or longer 6 GND 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 CVBS Output JST SM03B-SRSS-TB Pin Signal 1 GND 2 CVBS analog video output 3 GND (0V) CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details. In NTSC or PAL mode, there will be no SDI output signal available from TL8656. CVBS output connector J5 is available on Rev.B boards from September 26, 2018. TL8656 PCB Outline TL8656 | Production Kit Partnumber Content TL8656 3G/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm Type (1:n) TL8656-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-DIN-BNC-1 Connector cable with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter

Price on request

TL9801 | CVBS VIDEO
The TL9801 CVBS analog video interface from AIVION is a small form factor module to convert LVDS. Features: CVBS analog video output CVBS pass through from camera. Camera must be set to CVBS PAL or NTSC operating mode. Small form factor Small form factor 44mm x 38mm Camera Control USB2 UART based camera control Power 9V to 12V DC regulated Compliance RoHS compliant UL/UR compliant Temperature Range Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Download TL9801 Datasheet V1.0.0 TL9801 Block Diagram Power Input: 9V TO 12V regulated Power consumption (MP1110M-VC + TL9801) 3.2 W (cam motors inactive) Operating and Storage Conditions: Operating: Ambient Temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% Storage: Ambient Temperature (min/max): -20°C/+60°C = -4°F/140°FHumidity: 20%-80% TL9801 PCB Connectors J1 DC Jack Fitting plug inner/outer diameter: 2.55mm/5,5mm Center Pin DC Power Input - Shield GND J2 USB2 micro connector USB2 UART camera control interface USB2 UART chip Cypress CY7C65213 J5 MCX Coaxial connector Primary CVBS Output J9 Micro coaxial connector J6 CVBS Output (Board to wire connector) JST BM08B-SSRS-TB Pin Signal 1 CVBS Output (alternative to J5, do not connect both) 2 GND 3 Do not connect 4 Do not connect 5 Do not connect 6 GND (0V) 7 Do not connect 8 Do not connect TL9801 PCB Outline TL9801 | Production Kit Partnumber Content TL9801 CVBS Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm (Type 1:n) TL9801-EXT | Evaluation Extension Partnumber Content PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector CK-MCX-BNC MCX to BNC connector cable

Price on request