Single optical fiber line solution for block cameras

The TL4K1161 is a small form factor serial digital video (SDI) transmitter from AIVION. Camera video input signals are equalized, processed and output over coaxial connectors. Dual Link 3G-SDI output is compliant to SMPTE ST425-3, 2si mapping, FHD output is compliant to SMPTE ST425-1 level A standards. Camera control is accomplished by a transparent full duplex communication channel. Physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B-0200 cable kit is available as accessory. Features: SDI Video Output MCX 75 Ohm straight coaxial connectors Resolution up to 3840x2160p @ 30fps Dual Link 3G-SDI output of UHD formats 3G-SDI output of FHD formats 1.5G-SDI output of HD formats Automatic format detection Small Form Factor Small form factor 60mm x 46mm Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control IF Temperature Range and Power Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Application 4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530, FCB-ER8300, FCB-ES8230 and FCB-EW9500H camera blocks Industrial, medical, security, law enforcement, video production Download TL4K1161 V2.1.0 Datasheet TL4K1161 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 6.72W typ. (FCB-ER8300 lens steady +TL4K1161) P TL4K1161 = 3.72W (typ.) (12V DC supply, 3840x2160@25fps, TA = 25°C, Humidity = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1161 PCB Connectors J7 SDI output connector Link 1 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J8 SDI output connector Link 2 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J1 Power and Control IF Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 HDMI Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. TL4K1161 PCB Outline TL4K1161 | Production Kit Partnumber Content TL4K1161 Dual Link 3G-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1161-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws 2 x CK-MCX-BNC 2 MCX to BNC connector cable 

The TL4K1261 is a small form factor serial digital video (SDI) transmitter from AIVION with Power and Control over Coaxial Cable. Camera video input signals are equalized, processed, and output over straight DIN7A(10.23) connectors. Dual Link 3G-SDI output compliant to SMPTE ST425-3, 2si mapping, FHD output compliant o SMPTE ST425-1 level A Camera control is accomplished by a transparent full-duplex communication channel. The physical interface between camera and camera controller / PC is based on RS232 or 3.3V TTL level. TLCK-B cable kit is included and contains a 30wire micro coaxial cable for connecting TL4K1261 to FCB-ER8300 as well as a 10wire power supply and serial control cable harness. Features: SDI Video Output DIN7A (10.23) 75 Ohm straight coaxial connectors Resolution up to 3840x2160p @ 30fps Dual Link 3 Gbps UHD-SDI Transmitter Dual Out 3/1.5 Gbps FHD-SDI Transmitter 3G-SDI output of FHD formats 1.5G-SDI output of HD formats Automatic format detection PCOC Power and Control over Coaxial Cable 100m Camera Control RS232 level serial camera control interface 3.3V TTL level serial camera control IF Temperature Range and Power Ambient temperature (min/max): -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9V to 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Application 4K UHD and full HD integrated cameras based on Sony FCB-ER8550, FCB-ER8530 and FCB-ER8300 4K camera blocks Industrial, medical, security, law enforcement, video production Download TL4K1161 V1.1.0 Datasheet TL4K1261 Block Diagram Power Input: 9V to 12V DC regulated supply input voltage range Characteristics: PD = 6.72W typ. (FCB-ER8300 lens steady +TL4K1261) P TL4K1261 = 3.62W (typ.) (12V DC supply, 3840x2160@29.97fps, TA = 25°C, Humidity = 40%) Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80% TL4K1261 PCB Connectors J7 SDI output connector Link 1 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J8 SDI output connector Link 2 of DL-3G SDI output or 3G/1.5G-SDI FHD/HD output J1 Power and Control IF Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset- Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation. 6 GND (0V) 7 TXD_TTL (serial IF transmit 3.3V, optional) 8 RXD_TTL (serial IF receive 3.3V, optional) 9 RXD_232 (serial IF receive RS232 level) 10 TXD_232 (serial IF transmit RS232 level) J4 LVDS Video In 30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit. TL4K1261 PCB Outline TL4K1261 | Production Kit Partnumber Content TL4K1261 Dual Link 3G-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL4K1261-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-BRA Bracket and screws 2 x TL-EVK-DIN-BNC-1 2 Connector cables with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter 

The TL7051 Dual 3G/HD-SDI Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and supports several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M  HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7051 Revision D V.3.0.0 Datasheet TL7051 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7051 PCB Connectors J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7051 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7051 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND TL7051 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low ( < 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7051 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7051 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7051 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7051 Analog Video Output TL7051 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7051, the camera is also automatically powered. During power up all functions on TL7051, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7051. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7051 | Production Kit Partnumber Content TL7051 3G-SDI/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7051-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable

The AIVION TL8651 outputs serial digital video (SDI) up to 1080p60. It connects to the digital video interface of the block cameras and supports several progressive and interlace HDTV formats. Features: One 3G-SDI/HD-SDI Output Right angle DIN7A connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Board Side Mount The TL8651 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras. Tamron MP1010M-VC Tamron MP1110M-VC Camera Control RS232 and TTL level serial control interface Temperature Range and Power Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9.5V to 12V DC regulated Small form factor & Compliance Small form factor 60mm x 36mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Industrial, medical, security, inspection, ROV and Security Download TL8651 Datasheet TL8651 Block Diagram Power Input: 9.5V to 12V DC regulated supply input voltage range Power consumption (MP1110M-VC + TL8651) 4.7W (cam motors inactive) Power consumption value conditions: Power 12V DC, video mode 1080p60 Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80% Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80% TL8651 PCB Connectors J2 KEL USL00-30L-A Camera IF, use supplied 30wire micro coaxial cable only J4 3G/HD-SDI output KEL USL00-30L-A Default type: CEI C-SX113 (DIN7A / 1.0/2.3 coax system) J3 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC In 2 DC In 3 GND 4 GND 5 Reset / Shut Down, pull to GND to reset/shut down TL7650 and camera for reset, pull to GND for one second or longer 6 GND 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 CVBS Output JST SM03B-SRSS-TB Pin Signal 1 GND 2 CVBS analog video output 3 GND (0V) CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details. In NTSC or PAL mode, there will be no SDI output signal available from TL8651. CVBS output connector J5 is available on Rev.B boards from September 26, 2018. TL8651 PCB Outline TL8651 | Production Kit Partnumber Content TL8651 3G/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL8651-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-DIN-BNC-1 Connector cable with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter

The AIVION TL8656 outputs serial digital video (SDI) up to 1080p60 with Power and Control over Coaxial Cable and an external Trigger. It connects to the digital video interface of the block cameras and supports several progressive and interlace HDTV formats. Features: One 3G-SDI/HD-SDI Output Right angle DIN7A connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Board Side Mount The TL8656 video interface board can be mounted directly to the side of the camera module and the interface board form factor is optimal adjusted to the dimensions of the Tamron cameras. Tamron MP1010M-VC Tamron MP1110M-VC Camera Control RS232 and TTL level serial control interface Power and Control over Coaxial Cable Ext. Trigger Temperature Range and Power Operating ambient temperature range -5°C/+60°C Operating humidity range 20% to 80% Supply voltage 9.5V to 12V DC regulated Small form factor & Compliance Small form factor 60mm x 36mm RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Applications Industrial, medical, security, inspection, ROV and Security Download TL8656 Datasheet TL8656 Block Diagram Power Input: 9.5V to 12V DC regulated supply input voltage range Power consumption (MP1110M-VC + TL8656) 4.7W (cam motors inactive) Power consumption value conditions: Power 12V DC, video mode 1080p60 Ambient temperature +25°C/77°F Humidity 30% Operating and Storage Conditions: Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F Humidity: 20%-80% Storage Conditions: ATemperature (min/max): -20°C/+60°C = -4°F/140°F Humidity: 20%-80% TL8656 PCB Connectors J2 KEL USL00-30L-A Camera IF, use supplied 30wire micro coaxial cable only J4 3G/HD-SDI output KEL USL00-30L-A Default type: CEI C-SX113 (DIN7A / 1.0/2.3 coax system) J3 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC In 2 DC In 3 GND 4 GND 5 Reset / Shut Down, pull to GND to reset/shut down TL7650 and camera for reset, pull to GND for one second or longer 6 GND 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 CVBS Output JST SM03B-SRSS-TB Pin Signal 1 GND 2 CVBS analog video output 3 GND (0V) CVBS analog video output is available with Tamron MP1110M-VC only. In this case the camera monitoring mode (register 72) must be set to NTSC or PAL video. Refer to Tamron MP1110M-VC technical manual for further details. In NTSC or PAL mode, there will be no SDI output signal available from TL8656. CVBS output connector J5 is available on Rev.B boards from September 26, 2018. TL8656 PCB Outline TL8656 | Production Kit Partnumber Content TL8656 3G/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm Type (1:n) TL8656-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector TL-EVK-DIN-BNC-1 Connector cable with a 75Ω BNC Straight Plug and a 75Ω DIN Straight Plug. Certified for 3Gbps. Length 1 meter