TL7055 | 3G-SDI & analog YPbPr Interface

Price on request

AIVION Extension Kit
Block Cameras
Request an offer
Product number: TL7055-PK
Product information "TL7055 | 3G-SDI & analog YPbPr Interface"

The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector.

Features:

One 3G-SDI/HD-SDI Output

MCX connector
3G-SDI output compliant to SMPTE 424M level A
HD-SDI output compliant to SMPTE 292M

  • 1080p60 /59.94 /50 /30 /29.97 /25 Hz
  • 1080i60 /59.94 /50 Hz
  • 720p60 /59.94 /50 /30 /29.97 /25Hz

One Analog YsPbPr Output

8pin board to wire connector
Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV
Pb, Pr 0,7Vpp into 75 ohms

  • 1080p60 /59.94 /50 /30 /29.97 /25 Hz
  • 720p60 /59.94 /50 Hz

Camera Control

RS232 level serial camera control interface

Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface.

Temperature Range and Power

  • Operating ambient temperature range -10°C to +60°C
  • Operating humidity range 20% to 80%
  • Supply voltage 9V to 12V DC regulated

Small form factor & Compliance

  • Small form factor 46mm x 44mm
  • RoHS compliant (2002/05/EG and 2011/65/EU)
  • UL/UR compliant

Applications

Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements

Industrial, medical, security, law enforcement

TL7055 Block Diagram

AIVION TL7055

Power Input:

9V to 12V DC regulated supply input voltage range

Characteristics:

PD = 5.6W (FCB-EV7520A camera lens steady +TL7055)

PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%)

Operating and Storage Conditions:

Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU)

TL7055 PCB Connectors

AIVION TL7055

J8 SDI Video Output

Samtec MCX7-J-P-H-ST-SM1

J7 Camera Interface

KEL USL00-30L-A

30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.

J2 Power & Control

JST SM10B-SRSS-TB

Pin Signal
1 DC Supply voltage input
2 DC Supply voltage input
3 GND (0V)
4 GND (0V)
5 Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6 GND (0V)
7 Do not connect
8 Do not connect
9 RXD_232 (serial IF receive RS232 level)
10 TXD_232 (serial IF transmit RS232 level)

J4 YPbPr Video Output

JST SM08B-SRSS-TB

Pin Signal
1 HSync
2 VSync
3 GND (0V)
4 Pb signal output
5 GND (0V)
6 Ys signal output
7 GND (0V)
8 Pr signal output

TL7055 PCB Outline

AIVION TL7055

Board Operation: TL7055

TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal.
The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes).
The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as
7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels.
In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode.
TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera.
When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details).
The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055.

Test Pattern Generator (TPG) mode:

TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default.
TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards.
The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control.
The following VISCA commands are available for TPG control (all codes as hex values):
TPG activation:
87 01 00 24 01 08 0A FF
TPG deactivation:
87 01 00 24 01 08 06 FF
TPG pattern type 100% color bar:
87 01 00 24 04 00 04 FF
TPG pattern type multi pattern with moving block:
87 01 00 24 04 00 00 FF
TPG video standard:
87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50
pq = 19 for 720p60

TL7055 | Production Kit

Partnumber Content
TL7055 3G-SDI & analog Board
TLCK-B6 1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
3. TLCK-K08-150
8wire cable harness for the analog YsPbPr video output

TL7055-EXT | Evaluation Extension

Partnumber Content
EK-PA1100 Power supply and control interface board
PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
CK-MCX-BNC MCX to BNC connector cable
Control: RS232
Mount Option: Behind camera
Block Cameras: AIVION AZM-FS10L | Full-HD | 10x Optical Zoom | 12x Digital Zoom, AIVION AZM-FS30L | Full-HD | 30x Optical zoom | 12x Digital zoom, AIVION AZM-FS36L | Full-HD | 36x optical Zoom | 12x digital Zoom, Sony FCB EV-7520A | Full-HD | 30x optical Zoom | 12x digital Zoom, Tamron MP1010M-VC | Full-HD | 10x Optical Zoom | 0x Digital Zoom, Tamron MP1110M-VC | Full-HD | 10x Optical Zoom | 16x Digital Zoom
Interface Resolution: FHD 1080p (1920 × 1080 progressive scan), FHD 1080i (1920 × 1080 split into two interlaced fields of 540 lines), HD 720p (1280 × 720 progressive scan)
Interface: Analog YPbPr, Serial Digital Interface
Input: LVDS

0 of 0 reviews

Leave a review!

Share your experiences with other customers.


Optional products

EK-PA1100 | Power supply and control interface board
Power supply and control interface board

Price on request

PS-TE10A12 | 12 V AC to DC external power supply
12 V AC to DC external power supply

Price on request

TL-EVK-USB2-A-MICROB |  USB 2.0 Cable A- male and micor-B male
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector | 1,5m

Price on request

TL-EVK-BRA | Camera bracket
Camera bracket

Price on request

CK-MCX-BNC | MCX to BNC connector cable
MCX to BNC connector cable75 Ohm Optimized RG 179 Cable:Length 10cmBNC:75 Ohm Bulkhead Jack (10 μ" (0.25 μm) Gold on Center Contact, Nickel on Shell)MCX:75 Ohm MCX Right-angle Plug (30 μ" (0.76 μm) Gold on Center Contact, Gold Flash on Shell)

Price on request