Tamron MP1010M-VC | 2MP 10x Rolling Shutter Zoom Camera

The TL7050 Dual 3G/HD-SDI and DVI(HDMI) Output Video Transceiver module from AIVION connect to the digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M  HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz One HDMI Output HDMI connector (Kycon KDMIX_FS1V_WS) 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Video input and Compliance Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7050 V 2.5.0 Datasheet TL7050 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Characteristics: Power consumption TL7050: 260mA @ 12V DC (typ.) Operating and Storage Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7050 PCB Connectors J8 HDMI connector Kycon KDMIX_FS1V_WS J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7050 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output TL7050 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7050 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7050 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7050 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7050 Analog Video Output TL7050 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7050, the camera is also automatically powered. During power up all functions on TL7050, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7050. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7050 | Production Kit Partnumber Content TL7050 HDMI-HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7050-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter

The TL7051 Dual 3G/HD-SDI Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and supports several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Dual 3G-SDI/HD-SDI Output 3G-SDI output compliant to SMPTE 424M  HD-SDI output compliant to SMPTE 292M 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Robust RS485 differential serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7051 Revision D V.3.0.0 Datasheet TL7051 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7051 PCB Connectors J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7051 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J2 RS485 Control IF JST SM08B-SRSS-TB Pin Signal 1 TXD_P (to controller) 2 TXD_N (to controller) 3 RXD_N (from controller) 4 RXD_P (from controller) 5 GND 6 3.45V typ. (max. current 50mA) J5 Analog component YPbPr and CVBS output Requires TL7051 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND TL7051 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low ( < 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7051 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7051 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7051 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7051 Analog Video Output TL7051 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7051, the camera is also automatically powered. During power up all functions on TL7051, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7051. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7051 | Production Kit Partnumber Content TL7051 3G-SDI/HD-SDI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7051-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws CK-MCX-BNC MCX to BNC connector cable

The TL7052 DVI(HDMI) Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV formats. As no analog to digital conversion is done on these modules, excellent output image quality is achieved. Features: Video input Full automatic video input standard detection Digital 4Ch./8Ch. LVDS video input from camera One HDMI Output HDMI connector (Kycon KDMIX_FS1V_WS) 1080p60 /59.94 /50 /30 /29.97 /25 Hz 1080i60 /59.94 /50 Hz 720p60 /59.94 /50 /30 /29.97 /25Hz Analog HDTV YPbPr and CVBS Output HDTV YPbPr video output signals Analog SDTV CVBS video output signals Camera Control RS232 and TTL level serial control interface Temperature Range and Power Temperature monitoring with alert function Operating ambient temperature range -5°C/+60°C = 23°F/140°F Operating humidity range 20% to 80% Supply voltage 12V DC regulated Compliance RoHS compliant (2002/05/EG and 2011/65/EU) UL/UR compliant Download TL7052 V 2.4.0 Datasheet TL7052 Block Diagram Power Input: 7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks Operating Conditions: Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80% TL7052 PCB Connectors J8 HDMI connector Kycon KDMIX_FS1V_WS J3 Camera Interface KEL USL00-30L-A 30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit. J1 Power and Control JST SM10B-SRSS-TB Pin Signal 1 DC Supply voltage input 2 DC Supply voltage input 3 GND (0V) 4 GND (0V) 5 Reset / Shut Down, pull to GND to reset/shut down TL7052 and camera. For reset, pull to GND for one second or longer 6 GND (0V) 7 TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output 8 RXD_TTL (serial IF receive, 3.3V) 9 RXD_232 (serial IF receive, RS232 level) 10 TXD_232 (serial IF transmit, RS232 level) J5 Analog component YPbPr and CVBS output Requires TL7052 extended cable kit Pin Signal 1 Pr 2 GND 3 Pb 4 GND 5 Y 6 GND 6 CVBS 6 GND J4 24pin FFC Connector Power, Reset, Serial Control IF, analog Video TL7052 PCB Outline Temperature Alert Function When board temperature exceeds 80°C (176°F), red LED will be switched on. In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V) Test Pattern Generator TL7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details. To enable TPG mode, please execute these steps: 1. Set video mode with switches 2 and 3 2. Set pattern with switch 1 3. Set switch 4 to ON to enable TPG mode 4. Switch TL7052 power off and on again Note: TPG operation can be enabled with or without any camera connected to TL7052 Analog Video Output TL7052 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation. Reset Operation When applying power to TL7052, the camera is also automatically powered. During power up all functions on TL7052, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera. Camera Control Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7052. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection must be done be appropriate setting of switch-2. TL7052 | Production Kit Partnumber Content TL7052 HDMI Board TLCK-B 1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm 2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm, Type 1:n TL7052-EXT | Evaluation Extension Partnumber Content EK-PA1100 Power supply and control interface board PS-TE10A12 12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian. TL-EVK-USB2-A-MICROB USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector PTL-EVK-BRA Bracket and screws TL-EVK-HDMI High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter