Camera & Video Interfaces for Traffic Control
It is very common for system integrators to use block cameras in traffic control systems. The advantage for system integrators is the flexible interface concept. Our AIVION video interfaces make it possible to support systems with several SDI standards, HDMI, USB3 or even analogue standards.
For applications that need to process and analyse the content of the video, a USB3 interface can be used. All our AIVION interfaces use uncompressed low latency video. However, if a 4K or Full-HD video stream will be processed from a computing unit, it is essential to use a system that guarantees enough performance and cache to process the incoming video data without adding too much latency.
Another important factor for Traffic Control is the combination of low light capability and a good zoom factor. The new Sony FCB-EV9500L does combine those two needs very nicely. We do provide interfaces for 3G-SDI, HDMI, USB3, and even analogue standards for this camera.
Related Interface Products
The TL6032 interface is a HDTV USB 3.0 compliant video streaming capture solution from AIVION. As no analog to digital conversion is done on these modules, excellent output image quality is guaranteed.
Features:
USB 3.0 Video Output
Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format
1920x1080p @ 25Hz, 29.97Hz, 30 Hz
1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz
The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer
Small Form Factor
Small form factor 45mm x 40mm
USB
Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported)
Host computer must run a UVC capable operating system
Parallel up- and downstream of camera control and status data is possible (USB CDC)
Power
Full USB bus powered camera solution possible depending on camera
Power supply voltage for camera is generated onboard
Allows an external power supply
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Temperature Range
Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Download TL6032 V2.0.0 Datasheet
TL6032 Block Diagram
Power Input:
5V DC from USB3 port
Characteristics:
Power consumption (FCB-EV75xx + TL6035) 5.6W
Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive)
Power consumption TL6035: 2.7W/540mA@5V DC (max.)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80%
TL6032 PCB Connectors
J6 USB3 microB connector
Horizontal
J2 LVDS Video In
30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit.
J7 External Power Supply
Pin
Signal
1
Input voltage 5V to 7V DC
2
Input voltage 5V to 7V DC
3
System reset, pull to GND for reset
4
GND (0V)
5
GND (0V)
J9 RS232 UART Connector
Pin
Signal
1 to 7
do not connect
8
GND
9
RXD (host to camera)
10
TXD (camera to host)
TL6032 PCB Outline
Camera Power
Camera supply voltage is generated on TL6032 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera.
NOTE:
USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6032.
TL6032 EXTERNAL POWER OPTION:
TL6032 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6032 for the camera supply boost converter only. All other electronic devices on TL6032 are always powered from USB3 port. No adjustments on TL6032 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power.
Host (PC) - Device Communication
TL6032 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6032 via a serial communication channel (USB UART).
Connecting the TL6032 to the Host PC
Operating System Support
TL6032 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems:
Windows 7 (32 and 64bit)
Windows 8.1 (32 and 64bit)
Windows 10 (64bit, version 1511)
Driver Requirements
Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file.
Video Application on Host PC
Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information.
Controlling TL6032 from the Host PC via USB UART
TL6032 supports the USB UART functionality. FCB cameras connected to TL6032 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1).
TL6032 | Production Kit
Partnumber
Content
TL6032
USB 3.0 Board
TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL6032-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100-USB
Power supply and control interface board
PS-TE10A05
5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB-SA
USB to serial adapter
TL-EVK-BRA
Bracket and screws
TL-EVK-USB3-A-MICROB
USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector
Price on request
The TL6035 USB 3.0 interface board from AIVION is a tiny and easy to use HDTV USB3.0 video capture interface for the block cameras. The module receives digital video signals and sends UVC (USB Videl Class) compliant data packets to a connected host computer. Our compact TL6035 module enables the design of small camera systems that need only a single connection between camera and PC. Video stream, control data and power will be connected by a USB 3.0 cable. For camera blocks that need more than 900 mA during startup a Y-cable is required.
Features:
USB 3.0 Video Output
Up to 1080p30 uncompressed HDTV video data, 4:2:2 YUV format
1920x1080p @ 25Hz, 29.97Hz, 30 Hz
1280x720p @ 50Hz, 59.94Hz, 60Hz, 25Hz, 29.97Hz, 30Hz
The module receives digital video signals at the input and sends UVC (USB Video Class) compliant data packets containing digital video payload to a connected host computer
Small Form Factor
Small form factor 45mm x 40mm
USB
Operates always as Super Speed USB3.0 device (Host or OTG operation modes are not supported)
Host computer must run a UVC capable operating system
Parallel up- and downstream of camera control and status data is possible (USB CDC)
Power
Full USB bus powered camera solution possible depending on camera
Power supply voltage for camera is generated onboard
Allows an external power supply
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Temperature Range
Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Download TL6035 V2.0.0 Datasheet
TL6035 Block Diagram
Power Input:
5V DC from USB3 port
Characteristics:
Power consumption (FCB-EV75xx + TL6035) 5.6W
Power consumption (FCB-SE600 + TL6035) 3.5W (cam motors inactive)
Power consumption TL6035: 2.7W/540mA@5V DC (max.)
Operating and Storage Conditions:
Operating Conditions: Ambient temperature (min/max): -5°C/+60°C = 23°F/140°F - Humidity: 20%-80%
Storage Conditions: Temperature (min/max): -20°C/+60°C = -4°F/ 140°F - Humidity: 20%-80%
TL6035 PCB Connectors
J6 USB3 microB connector
Vertical
J2 LVDS Video In
30wire microcoax connector for 4K Block Cameras. Use 30wire micro coaxial cable supplied with cable kit.
J7 External Power Supply
Pin
Signal
1
Input voltage 5V to 7V DC
2
Input voltage 5V to 7V DC
3
System reset, pull to GND for reset
4
GND (0V)
5
GND (0V)
J9 RS232 UART Connector
Pin
Signal
1 to 7
do not connect
8
GND
9
RXD (host to camera)
10
TXD (camera to host)
TL6035 PCB Outline
Camera Power
Camera supply voltage is generated on TL6035 by a boost converter circuit. This circuit provides 9.55V DC (+/-3%) to the camera.
NOTE:
USB3.0 is specified for 4.5W maximum output power per USB3.0 port on a computer. However, many main boards used in desktop computer systems are able to provide more USB3 output power. In case of notebook and laptop computers, IPCs and SBCs, it has to be checked case by case if USB3 output power is sufficient or not. This is in the sole responsibility of the user of TL6035.
TL6035 EXTERNAL POWER OPTION:
TL6035 allows to use an external power supply in case USB3 power of the used computer is not sufficient. As described on page 3 of this document, external power can be input on J7. Using a voltage of 6V DC is recommended. In case an external power supply is used, this voltage is used on TL6035 for the camera supply boost converter only. All other electronic devices on TL6035 are always powered from USB3 port. No adjustments on TL6035 are required for using external power. When powering up such a configuration, external power must be supplied before or coincident with USB3 power.
Host (PC) - Device Communication
TL6035 operates always as USB device which sends UVC compliant video data to a host PC. The host also communicates with the TL6035 via a serial communication channel (USB UART).
Connecting the TL6035 to the Host PC
Operating System Support
TL6035 can be used with operating systems which fully support USB UVC type data and communication. Currently supported Microsoft Windows operating systems:
Windows 7 (32 and 64bit)
Windows 8.1 (32 and 64bit)
Windows 10 (64bit, version 1511)
Driver Requirements
Full UVC compliant driver is required. Such drivers are supplied with Microsoft Windows 7 and 8 . Manual driver installation is not necessary. For the USB UART feature, the class driver is used. Aivion provides suitable driver assignment files. Win 10 does not require such a driver assignment file.
Video Application on Host PC
Video display and recording can be done with standard application programs like VLC player, Mplayer or similar. VLC and Mplayer are open source based applications and can be free downloaded. If users want to design their own applications software, they are free to do so. All software programming tasks are OS based and have to be built upon UVC drivers. For further information please refer to Microsoft Windows API information.
Controlling TL6035 from the Host PC via USB UART
TL6035 supports the USB UART functionality. FCB cameras connected to TL6035 can be controlled via a virtual COM port. Any host software which uses COM ports can be used. The USB UART channel is transparent for any protocol. Communication speed is 9600bit/ s or 38400bit/s maximum. Other COM port settings are (8N1).
TL6035 | Production Kit
Partnumber
Content
TL6035
USB 3.0 Vertical Micro B USB Board
TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL6035-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100-USB
Power supply and control interface board
PS-TE10A05
5 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB-SA
USB to serial adapter
TL-EVK-BRA
Bracket and screws
TL-EVK-USB3-A-MICROB
USB 3.0 Cable with a USB 3.0-A male and a USB 3.0 micro-B male connector
Price on request
The TL7050 Dual 3G/HD-SDI and DVI(HDMI) Output Video Transceiver module from AIVION connect to the
digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV
formats. As no analog to digital conversion is done on these modules, excellent output image quality is
achieved.
Features:
Dual 3G-SDI/HD-SDI Output
3G-SDI output compliant to SMPTE 424M level A
HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
One HDMI Output
HDMI connector (Kycon KDMIX_FS1V_WS)
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Robust RS485 differential serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Video input and Compliance
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7050 V 2.5.0 Datasheet
TL7050 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Characteristics:
Power consumption TL7050: 260mA @ 12V DC (typ.)
Operating and Storage Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7050 PCB Connectors
J8 HDMI connector
Kycon KDMIX_FS1V_WS
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7050 and camera. For reset, pull to GND for
one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J2 RS485 Control IF
JST SM08B-SRSS-TB
Pin
Signal
1
TXD_P (to controller)
2
TXD_N (to controller)
3
RXD_N (from controller)
4
RXD_P (from controller)
5
GND
6
3.45V typ. (max. current 50mA)
J5 Analog component YPbPr and CVBS output
Requires TL7050 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output
TL7050 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V)
- In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7050 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7050 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7050 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7050
Analog Video Output
TL7050 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera.
In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation.
Reset Operation
When applying power to TL7050, the camera is also automatically powered. During power up all functions on TL7050, are reset and initialized.
During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7050. The interface is passed through to the camera that all VISCA protocol based software can be used.
Serial interface selection must be done be appropriate setting of switch-2.
TL7050 | Production Kit
Partnumber
Content
TL7050
HDMI-HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL7050-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
CK-MCX-BNC
MCX to BNC connector cable
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
Price on request
The TL7051 Dual 3G/HD-SDI Output Video Transceiver module from AIVION connects to the digital video interface (LVDS) of the block camera and supports several progressive and interlace HDTV formats. As no analog to digital conversion is done on
these modules, excellent output image quality is achieved.
Features:
Dual 3G-SDI/HD-SDI Output
3G-SDI output compliant to SMPTE 424M level A
HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Video input
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Robust RS485 differential serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7051 Revision D V.3.0.0 Datasheet
TL7051 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Operating Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7051 PCB Connectors
J9, J10 75 ohms MCX coaxial jack 3G/HD-SDI output
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7051 and camera. For reset, pull to GND for one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J2 RS485 Control IF
JST SM08B-SRSS-TB
Pin
Signal
1
TXD_P (to controller)
2
TXD_N (to controller)
3
RXD_N (from controller)
4
RXD_P (from controller)
5
GND
6
3.45V typ. (max. current 50mA)
J5 Analog component YPbPr and CVBS output
Requires TL7051 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
TL7051 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (
<
0.4V) - In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7051 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7051 board. In addition one out of two
test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7051 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7051
Analog Video Output
TL7051 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera. In some camera modes no or only limited analog video output might be available. Please refer to the related
camera documentation.
Reset Operation
When applying power to TL7051, the camera is also automatically powered. During power up all functions on TL7051, are reset and initialized. During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND).
This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7051. The interface is passed through to the camera that all VISCA protocol based software can be used. Serial interface selection
must be done be appropriate setting of switch-2.
TL7051 | Production Kit
Partnumber
Content
TL7051
3G-SDI/HD-SDI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL7051-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
CK-MCX-BNC
MCX to BNC connector cable
Price on request
The TL7052 DVI(HDMI) Output Video Transceiver module from AIVION connects to the
digital video interface (LVDS) of the block camera and support several progressive and interlace HDTV
formats. As no analog to digital conversion is done on these modules, excellent output image quality is
achieved.
Features:
Video input
Full automatic video input standard detection
Digital 4Ch./8Ch. LVDS video input from camera
One HDMI Output
HDMI connector (Kycon KDMIX_FS1V_WS)
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
Analog HDTV YPbPr and CVBS Output
HDTV YPbPr video output signals
Analog SDTV CVBS video output signals
Camera Control
RS232 and TTL level serial control interface
Temperature Range and Power
Temperature monitoring with alert function
Operating ambient temperature range -5°C/+60°C = 23°F/140°F
Operating humidity range 20% to 80%
Supply voltage 12V DC regulated
Compliance
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Download TL7052 V 2.4.0 Datasheet
TL7052 Block Diagram
Power Input:
7V to 12V DC regulated (13V DC absolute maximum) for other camera blocks
Operating Conditions:
Ambient temperature (min/max) -5°C/+60°C = 23°F/140°F Humidity: 20% - 80%
TL7052 PCB Connectors
J8 HDMI connector
Kycon KDMIX_FS1V_WS
J3 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J1 Power and Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset / Shut Down, pull to GND to reset/shut down TL7052 and camera. For reset, pull to GND for
one second or longer
6
GND (0V)
7
TXD_TTL (serial IF transmit, 3.3V) and/or temperature alert output
8
RXD_TTL (serial IF receive, 3.3V)
9
RXD_232 (serial IF receive, RS232 level)
10
TXD_232 (serial IF transmit, RS232 level)
J5 Analog component YPbPr and CVBS output
Requires TL7052 extended cable kit
Pin
Signal
1
Pr
2
GND
3
Pb
4
GND
5
Y
6
GND
6
CVBS
6
GND
J4 24pin FFC Connector
Power, Reset, Serial Control IF, analog Video
TL7052 PCB Outline
Temperature Alert Function
When board temperature exceeds 80°C (176°F), red LED will be switched on.
In addition such an event can be signalled on connector J1/pin7 by setting switch 3 (temp alert enable) to ON position. - In case board temperature is equal to or over 80°C (176°F), level on J1/pin7 will be held constant low (< 0.4V)
- In case board temperature is less than 80°C (176°F), level on J1/pin7 will be high (> 2.4V)
Test Pattern Generator
TL7052 has an integrated test pattern generator (TPG) which can be operated independent of any camera. The TPG can be enabled by setting onboard switch number 4 to ON position and repowering the TL7052 board. In addition one out of two test pattern and one out of four video standards can be selected by setting onboard switches 1, 2 and 3 accordingly. The following tables summarize all details.
To enable TPG mode, please execute these steps:
1. Set video mode with switches 2 and 3
2. Set pattern with switch 1
3. Set switch 4 to ON to enable TPG mode
4. Switch TL7052 power off and on again
Note: TPG operation can be enabled with or without any camera connected to TL7052
Analog Video Output
TL7052 provides analog HDTV YPbPr and analog SDTV CVBS video output signals. These signals are directly taken from the camera.
In some camera modes no or only limited analog video output might be available. Please refer to the related camera documentation.
Reset Operation
When applying power to TL7052, the camera is also automatically powered. During power up all functions on TL7052, are reset and initialized.
During operation a manual reset can be applied by pulling pin no. 5 of connector J1 to 0V (GND). This resets also the camera.
Camera Control
Camera control can be done by connecting a PC or CCU via RS485, RS232 or serial 3.3V TTL interface to TL7052. The interface is passed through to the camera that all VISCA protocol based software can be used.
Serial interface selection must be done be appropriate setting of switch-2.
TL7052 | Production Kit
Partnumber
Content
TL7052
HDMI Board
TLCK-B
1. TLCK-FL10-150
10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200
30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
TL7052-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe,
United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
PTL-EVK-BRA
Bracket and screws
TL-EVK-HDMI
High Speed HDMI Cable. HDMI-A male > HDMI-A male 4K 2 meter
Price on request
The TL7055 is a small form factor full HD 3G-SDI / HD-SDI plus analog YsPbPr output video transmitter for block cameras from AIVION. Camera LVDS video input signals are demultiplexed, processed and encoded. 3G/HD-SDI Video is output over a MCX connector. Analog YsPbPr Video is output over a 8pin board to wire connector.
Features:
One 3G-SDI/HD-SDI Output
MCX connector 3G-SDI output compliant to SMPTE 424M level A HD-SDI output compliant to SMPTE 292M
1080p60 /59.94 /50 /30 /29.97 /25 Hz
1080i60 /59.94 /50 Hz
720p60 /59.94 /50 /30 /29.97 /25Hz
One Analog YsPbPr Output
8pin board to wire connector Ys 1Vpp into 75 ohms, tri level sync amplitude 300mV Pb, Pr 0,7Vpp into 75 ohms
1080p60 /59.94 /50 /30 /29.97 /25 Hz
720p60 /59.94 /50 Hz
Camera Control
RS232 level serial camera control interface
Camera control is accomplished by a transparent full duplex communication channel. Physical layer between camera and camera controller is based on a RS232 level interface.
Temperature Range and Power
Operating ambient temperature range -10°C to +60°C
Operating humidity range 20% to 80%
Supply voltage 9V to 12V DC regulated
Small form factor & Compliance
Small form factor 46mm x 44mm
RoHS compliant (2002/05/EG and 2011/65/EU)
UL/UR compliant
Applications
Full HD integrated cameras with 3G-SDI plus analog HD YsPbPr output requirements
Industrial, medical, security, law enforcement
Download TL7055 Datasheet
TL7055 Block Diagram
Power Input:
9V to 12V DC regulated supply input voltage range
Characteristics:
PD = 5.6W (FCB-EV7520A camera lens steady +TL7055)
PTL7055 = 2.32W (typ.) (12V DC supply, 1920x1080@60fps, TA = 25°C, Humididty = 35%)
Operating and Storage Conditions:
Ambient temperature (min/max) -10°C/60°C = 14°F/140°F Humidity: 20% - 80% TL7055 is RoHS compliant (2002/05/EG and 2011/65/EU)
TL7055 PCB Connectors
J8 SDI Video Output
Samtec MCX7-J-P-H-ST-SM1
J7 Camera Interface
KEL USL00-30L-A
30wire microcoax connector for camera IF. Use 30wire micro coaxial cable supplied with cable kit.
J2 Power & Control
JST SM10B-SRSS-TB
Pin
Signal
1
DC Supply voltage input
2
DC Supply voltage input
3
GND (0V)
4
GND (0V)
5
Reset* Pull pin 5 to GND(0V) for 1ms or longer for reset, leave open for normal operation.
6
GND (0V)
7
Do not connect
8
Do not connect
9
RXD_232 (serial IF receive RS232 level)
10
TXD_232 (serial IF transmit RS232 level)
J4 YPbPr Video Output
JST SM08B-SRSS-TB
Pin
Signal
1
HSync
2
VSync
3
GND (0V)
4
Pb signal output
5
GND (0V)
6
Ys signal output
7
GND (0V)
8
Pr signal output
TL7055 PCB Outline
Board Operation: TL7055
TL7055 operates fully automatic with respect to outputting video over SDI and analog YsPbPr. Sync is provided as SMPTE compliant tri level sync on the Y signal. The output video standard is defined by the video standard of the video signal source. TL7055 locks automatically to the signal source as long as the provided video format is supported (see page 1 for supported video modes). The video source is typically a block type camera or equivalent device providing digital 4:2:2/8bit per component video as 7:1 serialized data stream. This data stream is transmittted over 4 (single mode) or 8 (dual mode) LVDS channels from the video source and is received and demultiplexed by the video processor on TL7055. In all cases embedded sync (SAV/EAV) codes must be present in the LVDS data streams. In case of dual mode it must be present in both channels. In case of block type cameras, the respective camera register must be set correctly for single or dual LVDS output mode. TL7055 requires dual LVDS mode in case of 1080p60, 1080p59.94 or 1080p50 video. For all other video standards single LVDS must be choosen in the camera. When the video standard and/or the LVDS output mode is changed in the camera, TL7055 must get a power reset cycle to lock on the new system settings. Such a reset cycle can be achieved by switching power off and on again or by applying a reset to pin 5 of J2 (see page 2 for details). The camera (or video source) can be controlled over a transparent, full duplex data channel. TL7055 does not process or change any control data. The full duplex data channel can be accessed by the RS232 interface of TL7055.
Test Pattern Generator (TPG) mode:
TL7055 has an integrated test pattern generator which can be activated and deactivated by VISCA commands. Such settings are not permanently stored. That means every time power is switched off and on again, the TPG is not activated as default. TPG can be activated even when no camera or video source is present. TPG starts always with providing a 100% color bar pattern in 1080p60 mode. This can be changed by VISCA commands afterwards. The TPG is seen as a VISCA device using highest VISCA address 0x87. It is required to use a baud rate of 9600bps with 8N1 serial data configuration for TPG control. The following VISCA commands are available for TPG control (all codes as hex values): TPG activation: 87 01 00 24 01 08 0A FF TPG deactivation: 87 01 00 24 01 08 06 FF TPG pattern type 100% color bar: 87 01 00 24 04 00 04 FF TPG pattern type multi pattern with moving block: 87 01 00 24 04 00 00 FF TPG video standard: 87 01 00 24 01 0p 0q FF pq = 01 for 1080p50 pq = 09 for 1080p60 pq = 11 for 720p50 pq = 19 for 720p60
TL7055 | Production Kit
Partnumber
Content
TL7055
3G-SDI & analog Board
TLCK-B6
1. TLCK-FL10-150 10 pin flying leads cable for power and control(RS232/TTL), length 15cm
2. TLCK-K30-200 30 pin KEL USL type micro coaxial cable, connector on both sides, length 20cm
3. TLCK-K08-150 8wire cable harness for the analog YsPbPr video output
TL7055-EXT | Evaluation Extension
Partnumber
Content
EK-PA1100
Power supply and control interface board
PS-TE10A12
12 V AC to DC external power supply with interchangeable blade kit for USA, Europe, United Kingdom and Australian.
TL-EVK-USB2-A-MICROB
USB 2.0 Cable with a USB 2.0-A male and a USB 2.0 micro-B male connector
CK-MCX-BNC
MCX to BNC connector cable
Price on request
Related Camera Products
The FCB-EV7520 camera block incorporates a 1/2.8-type Exmor RTM CMOS sensor, providing Full-HD video with extraordinary sensitivity. In addition, the Sony block camera includes STARVISTM technology to realize high picture
quality in visible light and near-infrared light. With 30x optical zoom and either HD or Full-HD capability, the camera inherits a multitude of Sony’s FCB features, including Auto ICR, Spherical Privacy Zone Masking,
and Defog.
Sony FCB-EV7520 Features
30x Enhanced Optical Zoom
Digital Zoom 12x (360x with optical zoom)
Full HD (1080p/60)
Image Sensor 1/2.8-type Exmor R CMOS
Minimum illumination Colour: 0.01 lx (F1.6,AGC on, 1/30 s)
Defog · High Light Compensation · Wide Dynamic Range
Super Image Stabilizer
Auto IR-cut Filter Removal
Spehrical privacy zone masking
Noise reduction
Slow AE response
Datasheet Sony FCB-7520 Series
Overview Features FCB-EV7520
Capture crisp, clear Full-HD (1080/60p)
Even in low-light environments, the high-performance 1/2.8-type Exmor CMOS image sensor achieves outstanding Full-HD (1920 x 1080) picture quality. Progressive scanning assures smoother pictures with reduced blur – ideal for capturing
the detail in moving images.
Get a steadier picture with the image stabilizer.
The camera's built-in image stabilizer function counters the effect of blurred, shaky images caused by low-frequency vibration. It is helpful for outdoor surveillance and traffic monitoring applications, mainly if the camera is used
on a bridge or mounting pole where it is subjected to wind or mechanical vibration.
Stable Zoom
Image stabilizer and optical/digital zoom are combined to improve image quality while maintaining the original horizontal viewing angle. This does not affect the image size and reduces blu.
2D/3D noise reduction
Advanced noise reduction technology filters noise from the image for clearer results, especially in low-light conditions. Noise reduction can be selected from five levels to suit a wide range of operating environments.
Wide dynamic range
Wide-D image processing technology allows one to see clear, detailed images in high-contrast or backlit environments. Models now support an extensive 130 dB dynamic range activated via the VISCA command.
De-fog
The de-fog feature allows more precise and natural viewing in foggy or misty scenes. The camera detects the haze level and automatically applies the required effects when this feature is activated. Depending on user requirements, the
level of these effects can be adjusted via the VISCA command.
HLC (High Light Compensation)
HLC technology helps to improve, for example, the visibility of license plates when bright headlights are shot under low-light conditions. The bright parts in the image are masked and compensated automatically to achieve better visibility.
Auto ICR (Auto IR-cut Filter Removal)
In low-light conditions, the camera automatically switches from Day to Night mode, removing the IR-cut filter to boost sensitivity for clear pictures in near-darkness. The spherical privacy zone masking feature enables areas of view
to be selectively masked for privacy. Masked areas are automatically interlocked with the camera’s pan/tilt/zoom movements.
Privacy Zone Masking
Privacy Zone Masking protects private objects and areas such as house windows, entrances, and exits within the camera’s range of vision but is not subject to surveillance. Privacy zones can be masked on the monitor to protect privacy.
Wide range of features for versatile operation
Versatile operation is ensured by a wide range of functions and adjustments, including White Balance modes; Picture effects (E-Flip, Nega Art, Black & White, Mirror Image, Colour Enhancement); Motion Detection/Alarm; Picture freeze;
Temperature readout; Slow AE response; Electronic shutter/ slow shutter; and Title display/Camera mode display (English).
Sony FCB-EV7520 Specifications
Feature
Sony FCB-EV7520
Image sensor
1/2.8-type Exmor R CMOS
Image sensor (Number of effective pixels)
Approx.2.13 Megapixels
Signal system
1080p/59.94,1080p/50, 1080p/60, 1080p/30, 1080p/29.97, 1080p/25, 1080i/59.94, 1080i/50, 1080i/60, 1080i/30, 720p/59.94, 720p/50, 720p/60, 720p/30, 720p/29.97, 720p/25, NTSC, PAL
Minimum illumination (50%) High sensitivity mode
Colour: 0.01 lx (F1.6, AGC on, 1/30s)
Minimum illumination (50%) Normal mode
Colour: 0.1 lx (F1.6, AGC on, 1/30s)
S/N ratio
More than 50 dB
Gain Auto/Manual
Auto/Manual 0 dB to 50.0dB (0 to 28 steps +2 step/ total 15 steps)
Gain Max. Gain Limit
Max. Gain Limit 10.7 dB to 50.0 dB (6 to 28 steps +2 tep/ total 12 steps)
Shutter speed
1/1 s to 1/10,000 s, 22 steps
Sync system
Internal
Exposure control
Auto, Manual, Priority mode (shutter priority & iris priority), Bright, EV compensation, Slow AE
Backlight compensation
Yes
Aperture control
16 steps
White balance
Auto, ATW, Indoor, Outdoor, Outdoor Auto, Sodium Vapor Lamp (Fix/Auto/Outdoor Auto), One-push, Manual
Lens
30x optical zoom f = 4.3 mm (wide) to 129.0 mm (tele) F1.6 to F4.7
Digital zoom
12x (360x with optical zoom)
Focusing system
Auto (Sensitivity: normal, low), One-push AF, Manual, Interval AF, Zoom Trigger AF, Focus compensation in ICR on
Horizontal viewing angle 1080p mode
63.7° (wide end) to 2.3° (tele end)
Horizontal viewing angle 720p mode
63.7° (wide end) to 2.3° (tele end)
Horizontal viewing angle SD
47.8° (wide end) to 1.7° (tele end)
Minimum object distance
10 mm (wide end) to 1200 mm (tele end) (Default: 300 mm)
Auto ICR
Yes
Wide-D
Yes (120 dB)
Visibility Enhancer
Yes
De-fog
Yes
HLC
Yes
Noise reduction
Yes (6 steps)
Image stabilization
Yes
StableZoom
Yes
Spherical privacy zone masking
Yes
Motion detection
Yes
Alarm
Yes
Slow AE response
Yes
Picture effects
E-Flip, Nega Art, Black & White, Mirror image, Colour enhancement
Picture freeze
Yes
Slow shutter
Yes
Temperature readout
Yes
Title display
Yes
Camera mode display
20 characters/line, max. 11 lines
Key switch control
Yes
Camera operation switch
Yes
Video output HD Analog
N/A
Video output HD Digital
Digital:Y/Cb/Cr 4:2:2 via LVDS (Signal format conforms to SMPTE 274/SMPTE 296.)
Video output SD
VBS
Camera control interface
VISCA (CMOS 5 V level) Baud rate: 9.6 Kbps, 19.2 Kbps, 38.4 Kbps, 115.2 Kbps, Stop bit: 1 bit
Power requirements
6.0 V to 12.0 V DC
Power consumption - Focus inactive
3.2 W (zoom/focus inactive)
Power consumption - Focus active
4.0 W (zoom/focus active)
Operating temperature
-5°C to +60°C (23°F to 140°F)
Storage temperature
-20°C to +60°C (-4°F to 140 °F)
Operating humidity
20% to 80%, Absolute humidity: 36 g/m3
Storage humidity
20% to 95%, Absolute humidity: 36 g/m3
Dimensions (W x H x D)
50.0 x 60.0 x 89.7 mm (2 x 2 3/8 x 3 5/8 inches)
Mass
255 g (9.0 oz)
Sony FCB-7520 Dimensions
Sony FCB-EV7520 Front
Sony FCB-EV7520 Rear
Sony FCB-EV7520 Top
Sony FCB-EV7520 Bottom
Sony FCB-EV7520 Left
Sony FCB-EV7520 Right
Price on request
Compact size block camera with 30x enhanced optical zoom and a 1/1.8 sensor. This Full HD model with LVDS output is optimal for environments with harsh conditions. The new super image stabilizer has greatly improved blur suppression
compared to conventional models.
Sony FCB-EV9500L Features
Full HD (1080p/60)
LVDS
30x Enhanced Optical Zoom
High Sensitivity
Super Image Stabilizer
Flare reduction with the new iris
Color image acquisition during ICR ON
Spot Focus · Spot AE · Spot AWB
Wide Dynamic Range (Wide-D)
Visibility Enhancer (VE)
Datasheet Sony FCB-9500 Series
Overview Features FCB-EV9500L
High Resolution
Utilizing a 4M sensor and sharp lens achieve superior resolution and accurate image representation with the evolved AF/AE/ AWB functions even in low light environments. Combined with enhanced optical zoom achieve a high image quality
from the Wide end to the Tele end.
High Sensitivity
Through introduction of new cell structures and circuit technology, the series efficiently uses light, achieving twice the sensitivity compared to conventional image sensors. Consequently, clear images can be captured even during the
night and in dark environments.
Super Image Stabilizer
Enables capturing of highly precise video with reduced blurring even in harsh environments with strong vibrations by greatly improving blur suppression and image stabilizer. The camera is during full HD or HD output equipped with the
Super and Super modes. Applying a wide correction area using 4M pixels the camera series suppresses blurs from strong vibrations and rotational vibrations compared to conventional models.
Super
Suppresses strong vibrations with a wider correction area compared to conventional electronic vibration suppressors.
Super +
By employing a wider correction area than “Super,” “Super+” suppresses intense vibrations that cannot be suppressed with “Super.” Potential application: Shipboard, attachments for ITS surveillance, on bridges, drones, vehicles,
etc.
Starvis 1/1.8-type CMOS sensor
The Sony FCB-EV9500L Sony blockcamera is equipped with an approximately 417 million- effective-pixel, 1/1.8-type high sensitive, AR-coated (anti-reflective coating) CMOS sensor. With a high spectral sensitivity value in near infrared
to infrared, it is especially effective for security uses. Furthermore, the AR coating minimizes the ghost phenomenon and enables capturing of images without missing crucial information even during the night and in dark environments.
30x Enhanced Optical Zoom
Using a compact lens designed for resolutions up to 8M the camera maximizes the coverage of the 4M sensor. The newly designed lens provides high resolution and low aberration, making it capable of capturing high resolution images
that span from the Tele end from the screen center to the surrounding edges. There is no image deterioration using the 30x enhanced optical zoom. Experience full sharpness and dramatically reduced chromatic aberration in full
HD output and also achieve images with sharp resolution during 4M output.
Flare reduction with the new iris
Diamond flares and ghosts that occur on lenses disrupts focusing and deteriorates the image quality. The new lens adopts 7 blades compared to the conventional 2 blades, improving this phenomenon by generating fine circular flares,
and thus greatly improving image quality.
Color image acquisition during ICR ON
On conventional models, only black and white images are achieved while the IR cut filter was removed. The new ICR ON COLOR function enables the camera to capture shots with color even when the IR cut filter is removed. It is effective
for color visibility in dark environments. The precision of color reproduction varies depending on the light source and brightness.
Spot Focus · Spot AE · Spot AWB
Enables functioning of AF, AE, and AWB only in specified areas within the screen. Enables independent specification of any rectangle of the entire screen divided in 6 x 8. For example, if the subject location is specified with
Spot AE, enables capturing of images with Exposure effects reduced even if brightness changes occur outside the specified frame.
Adjustable ROIs
Screen divided in 6 x 8
Wide Dynamic Range (Wide-D)
Wide-D mode is a function for dividing an image into several blocks for correcting blocked-up shadows and blown-out highlights in accordance with the intensity difference. It enables image acquisition in which portions ranging
from dark to light can be recognized, even when capturing a subject with a large intensity difference that is backlit or includes extremely light regions of interest.
Wide Dynamic Range Off
Wide Dynamic Range On
Sony FCB-EV9500L Specifications
Specification
FCB-EV9500L (Full HD· LVDS)
Basic Features
Image Sensor (Number of effective pixels)
1/1.8-type STARVISTM CMOS Sensor (Approx. 4.17M pixels)
Output Image Size (H x V)
1920x1080, 1280x720
Signal System
1080p/60, 1080p/59.94, 1080p/50, 1080p/30, 1080p/29.97, 1080p/25, 1080i/60, 1080i/59.94, 1080i/50, 720p/60, 720p/59.94, 720p/50, 720p/30, 720p/29.97, 720p/25
Minimum Illumination (50%, High Sensitivity Mode ON)
ICR-Off mode: 0.009 lx (Shutter Speed: 1/30 s), 0.0012 lx (Shutter Speed: 1/4 s or 1/3 s) ICR-On mode: 0.00008 lx (Shutter Speed: 1/30 s), 0.000005 lx (Shutter Speed: 1/4 s or 1/3 s, 30%)
Minimum Illumination (50%, High Sensitivity Mode OFF)
ICR-Off mode: 0.09 lx (Shutter Speed: 1/30 s), 0.012 lx (Shutter Speed: 1/4 s or 1/3 s) ICR-On mode: 0.00063 lx (Shutter Speed: 1/30 s)
Recommended Illumination
100 lx to 100,000 lx
Image S/N
Wide end to Tele end - 4.8 s (Focus Tracking ON), 2.9 s (Focus Tracking OFF) Wide end to Digital 12x tele - 6.1 s (29.97p/59.94p), 6.4 s(25p/50p)
Gain
Auto/Manual (0 dB to 50.0 dB), 0 to 28 steps
Shutter Speed
1/1 to 1/10000 s, 22 steps
Sync System
Internal
Exposure Control
0 dB to ± 10.5 dB, 15 steps
Backlight Compensation
Yes
Gamma
Standard / Straight gamma
Aperture Control
16 steps
White Balance
Auto, ATW, Indoor, Outdoor, One Push WB, Manual WB, Outdoor Auto, Sodium Vapor Lamp (Fix/Auto/Outdoor Auto), Spot AWB
AE (Auto Exposure Mode)
Full Auto, Manual, Priority mode (shutter/iris), EV compensation, Spot AE, Slow AE
Zoom
30x Enhanced Optical Zoom 36x StableZoom and 12x Digital Zoom - StableZoom increases the magnification by combining optical zoom and digital zoom - FCB-EW9500H: For 1080p, 1080i, and 720p only.
Lens (wide to tele)
f = 6.5 mm to 162.5 mm, F1.6 to 4.8
Zoom Mode
Standard Mode / Variable Mode / Direct Mode
Zoom Movement Speed
Wide end to Tele end - 4.8 s (Focus Tracking ON), 2.9 s (Focus Tracking OFF) Wide end to Digital 12x tele - 6.1 s (29.97p/59.94p), 6.4 s(25p/50p) Digital wide to Digital 12x tele - 1.4 s (29.97p/59.94p), 1.6
s (25p/50p)
Focusing System
Auto Focus (Normal AF, Interval AF, Zoom Trigger AF [Sensitivity: normal, low]), Manual (Standard, Variable, Direct), One Push Trigger, Full Scan One Push Trigger, Near Limit, ICR-on Correction, Spot Focus
Focus Movement Time
∞ to Near: 1.4 s
Horizontal Viewing Angle
58.1° to 2.3°
Minimum Object Distance (wide end to tele end)
100 mm to 1200mm
Camera Features
Auto ICR
Yes
Wide Dynamic Range (Wide-D)
Yes
Visibility Enhancer
Yes
Defog
Yes (low/mid/high)
Noise Reduction
Yes (3D + 2D / Independent setting (3D, 2D))
Progressive Scan Mode
Yes
Image Stabilization
Yes: Super image stabilizer (Super / Super+ FCB-EW9500H: For 1080p, 1080i, and 720p only.)
Spot Light Avoidance
Yes
Motion Detection
Yes
Privacy Zone Masking
Yes
Alarm
Yes
Slow AE Response
Yes
Picture Effects
Black White (Monochrome Image)
Picture Freeze
Yes
Electronic-Flip (E-FLIP)
Yes
Mirror Image
Yes
Slow Shutter
Yes
Temperature Readout
Yes
Title Display
Yes (20 characters / line, max. 11lines)
Camera Mode Display
Yes (English)
Interface
Video Output
Digital : Y/Pb/Pr 4:2:2 (LVDS)
(Y: 8 bit, C: 8 bit, Vsync, Hsync, Field, Clock) (SMPTE274M/SMPTE296M)
Camera Control Interface
VISCA protocol (CMOS 3.3V Level, 5.5V tolerance); Baud Rate : 9.6 kbps, 19.2 kbps, 38.4 kbps, 115.2 kbps, Stop bit: 1 bit
General
Power Requirements
7.0 V to 12.0 V DC
Power Consumption
6.1 W (When motor operates: 7.8W)
Operating Temperature
"-5 °C to +60 °C (23 °F to +140 °F)"
Storage Temperature
"-20 °C to +60 °C (–4 °F to +140 °F)"
Operating Humidity
20% to 80% (Absolute humidity: 36 g/m3)
Storage Humidity
20% to 95% (Absolute humidity: 36 g/m3)
Dimensions (W x H x D)
56.0 x 64.0 x 125 mm (2 1/4 × 2 5/8 × 5 in.)
Mass
Approx. 439 g (15 oz.)
Price on request